/* USER CODE BEGIN Header */
/**
******************************************************************************
* @file stm32wlxx_hal_conf.h
* @author MCD Application Team
* @brief HAL configuration file.
******************************************************************************
* @attention
*
* Copyright (c) 2020 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
*/
/* USER CODE END Header */
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32WLxx_HAL_CONF_H
#define STM32WLxx_HAL_CONF_H
#ifdef __cplusplus
extern "C" {
#endif
/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/
/* ########################## Module Selection ############################## */
/**
* @brief This is the list of modules to be used in the HAL driver
*/
#define HAL_MODULE_ENABLED
#define HAL_ADC_MODULE_ENABLED
/*#define HAL_COMP_MODULE_ENABLED */
/*#define HAL_CRC_MODULE_ENABLED */
/*#define HAL_CRYP_MODULE_ENABLED */
/*#define HAL_DAC_MODULE_ENABLED */
/*#define HAL_GTZC_MODULE_ENABLED */
/*#define HAL_HSEM_MODULE_ENABLED */
/*#define HAL_I2C_MODULE_ENABLED */
/*#define HAL_I2S_MODULE_ENABLED */
/*#define HAL_IPCC_MODULE_ENABLED */
/*#define HAL_IRDA_MODULE_ENABLED */
/*#define HAL_IWDG_MODULE_ENABLED */
/*#define HAL_LPTIM_MODULE_ENABLED */
/*#define HAL_PKA_MODULE_ENABLED */
/*#define HAL_RNG_MODULE_ENABLED */
#define HAL_RTC_MODULE_ENABLED
/*#define HAL_SMARTCARD_MODULE_ENABLED */
/*#define HAL_SMBUS_MODULE_ENABLED */
#define HAL_SPI_MODULE_ENABLED
#define HAL_SUBGHZ_MODULE_ENABLED
#define HAL_TIM_MODULE_ENABLED
#define HAL_UART_MODULE_ENABLED
/*#define HAL_USART_MODULE_ENABLED */
/*#define HAL_WWDG_MODULE_ENABLED */
#define HAL_EXTI_MODULE_ENABLED
#define HAL_CORTEX_MODULE_ENABLED
#define HAL_DMA_MODULE_ENABLED
#define HAL_FLASH_MODULE_ENABLED
#define HAL_GPIO_MODULE_ENABLED
#define HAL_PWR_MODULE_ENABLED
#define HAL_RCC_MODULE_ENABLED
/* ########################## Register Callbacks selection ############################## */
/**
* @brief This is the list of modules where register callback can be used
*/
#define USE_HAL_ADC_REGISTER_CALLBACKS 0u
#define USE_HAL_COMP_REGISTER_CALLBACKS 0u
#define USE_HAL_CRYP_REGISTER_CALLBACKS 0u
#define USE_HAL_DAC_REGISTER_CALLBACKS 0u
#define USE_HAL_I2C_REGISTER_CALLBACKS 0u
#define USE_HAL_I2S_REGISTER_CALLBACKS 0u
#define USE_HAL_IRDA_REGISTER_CALLBACKS 0u
#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0u
#define USE_HAL_PKA_REGISTER_CALLBACKS 0u
#define USE_HAL_RNG_REGISTER_CALLBACKS 0u
#define USE_HAL_RTC_REGISTER_CALLBACKS 0u
#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0u
#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0u
#define USE_HAL_SPI_REGISTER_CALLBACKS 0u
#define USE_HAL_SUBGHZ_REGISTER_CALLBACKS 0u
#define USE_HAL_TIM_REGISTER_CALLBACKS 0u
#define USE_HAL_UART_REGISTER_CALLBACKS 0u
#define USE_HAL_USART_REGISTER_CALLBACKS 0u
#define USE_HAL_WWDG_REGISTER_CALLBACKS 0u
/* ########################## Oscillator Values adaptation ####################*/
/**
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
* This value is used by the RCC HAL module to compute the system frequency
* (when HSE is used as system clock source, directly or through the PLL).
*/
#if !defined (HSE_VALUE)
#define HSE_VALUE 32000000UL /*!< Value of the External oscillator in Hz */
#endif /* HSE_VALUE */
#if !defined (HSE_STARTUP_TIMEOUT)
#define HSE_STARTUP_TIMEOUT 100UL /*!< Time out for HSE start up, in ms */
#endif /* HSE_STARTUP_TIMEOUT */
/**
* @brief Internal Multiple Speed oscillator (MSI) default value.
* This value is the default MSI range value after Reset.
*/
#if !defined (MSI_VALUE)
#define MSI_VALUE 4000000UL /*!< Value of the Internal oscillator in Hz*/
#endif /* MSI_VALUE */
/**
* @brief Internal High Speed oscillator (HSI) value.
* This value is used by the RCC HAL module to compute the system frequency
* (when HSI is used as system clock source, directly or through the PLL).
*/
#if !defined (HSI_VALUE)
#define HSI_VALUE 16000000UL /*!< Value of the Internal oscillator in Hz*/
#endif /* HSI_VALUE */
/**
* @brief Internal Low Speed oscillator (LSI) value.
*/
#if !defined (LSI_VALUE)
#define LSI_VALUE 32000UL /*!< LSI Typical Value in Hz*/
#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
The real value may vary depending on the variations
in voltage and temperature. */
/**
* @brief External Low Speed oscillator (LSE) value.
* This value is used by the UART, RTC HAL module to compute the system frequency
*/
#if !defined (LSE_VALUE)
#define LSE_VALUE 32768UL /*!< Value of the External oscillator in Hz*/
#endif /* LSE_VALUE */
/**
* @brief Internal Multiple Speed oscillator (HSI48) default value.
* This value is the default HSI48 range value after Reset.
*/
#if !defined (HSI48_VALUE)
#define HSI48_VALUE 48000000UL /*!< Value of the Internal oscillator in Hz*/
#endif /* HSI48_VALUE */
#if !defined (LSE_STARTUP_TIMEOUT)
#define LSE_STARTUP_TIMEOUT 5000UL /*!< Time out for LSE start up, in ms */
#endif /* LSE_STARTUP_TIMEOUT */
/* Tip: To avoid modifying this file each time you need to use different HSE,
=== you can define the HSE value in your toolchain compiler preprocessor. */
/* ########################### System Configuration ######################### */
/**
* @brief This is the HAL system configuration section
*/
#define VDD_VALUE 3300U /*!< Value of VDD in mv */
#define TICK_INT_PRIORITY ((1uL <<__NVIC_PRIO_BITS) - 1uL) /*!< tick interrupt priority (lowest by default) */
#define USE_RTOS 0U
#define PREFETCH_ENABLE 0U
#define INSTRUCTION_CACHE_ENABLE 1U
#define DATA_CACHE_ENABLE 1U
/* ########################## Assert Selection ############################## */
/**
* @brief Uncomment the line below to expanse the "assert_param" macro in the
* HAL drivers code
*/
/* #define USE_FULL_ASSERT 1 */
/* ################## SPI peripheral configuration ########################## */
/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
* Activated: CRC code is present inside driver
* Deactivated: CRC code cleaned from driver
*/
#define USE_SPI_CRC 1U
/* ################## CRYP peripheral configuration ########################## */
#define USE_HAL_CRYP_SUSPEND_RESUME 1U
/* Includes ------------------------------------------------------------------*/
/**
* @brief Include module's header file
*/
#ifdef HAL_DMA_MODULE_ENABLED
#include "stm32wlxx_hal_dma.h"
#endif /* HAL_DMA_MODULE_ENABLED */
#ifdef HAL_ADC_MODULE_ENABLED
#include "stm32wlxx_hal_adc.h"
#endif /* HAL_ADC_MODULE_ENABLED */
#ifdef HAL_COMP_MODULE_ENABLED
#include "stm32wlxx_hal_comp.h"
#endif /* HAL_COMP_MODULE_ENABLED */
#ifdef HAL_CORTEX_MODULE_ENABLED
#include "stm32wlxx_hal_cortex.h"
#endif /* HAL_CORTEX_MODULE_ENABLED */
#ifdef HAL_CRC_MODULE_ENABLED
#include "stm32wlxx_hal_crc.h"
#endif /* HAL_CRC_MODULE_ENABLED */
#ifdef HAL_CRYP_MODULE_ENABLED
#include "stm32wlxx_hal_cryp.h"
#endif /* HAL_CRYP_MODULE_ENABLED */
#ifdef HAL_DAC_MODULE_ENABLED
#include "stm32wlxx_hal_dac.h"
#endif /* HAL_DAC_MODULE_ENABLED */
#ifdef HAL_EXTI_MODULE_ENABLED
#include "stm32wlxx_hal_exti.h"
#endif /* HAL_EXTI_MODULE_ENABLED */
#ifdef HAL_FLASH_MODULE_ENABLED
#include "stm32wlxx_hal_flash.h"
#endif /* HAL_FLASH_MODULE_ENABLED */
#ifdef HAL_GPIO_MODULE_ENABLED
#include "stm32wlxx_hal_gpio.h"
#endif /* HAL_GPIO_MODULE_ENABLED */
#ifdef HAL_GTZC_MODULE_ENABLED
#include "stm32wlxx_hal_gtzc.h"
#endif /* HAL_GTZC_MODULE_ENABLED */
#ifdef HAL_HSEM_MODULE_ENABLED
#include "stm32wlxx_hal_hsem.h"
#endif /* HAL_HSEM_MODULE_ENABLED */
#ifdef HAL_I2C_MODULE_ENABLED
#include "stm32wlxx_hal_i2c.h"
#endif /* HAL_I2C_MODULE_ENABLED */
#ifdef HAL_I2S_MODULE_ENABLED
#include "stm32wlxx_hal_i2s.h"
#endif /* HAL_I2S_MODULE_ENABLED */
#ifdef HAL_IPCC_MODULE_ENABLED
#include "stm32wlxx_hal_ipcc.h"
#endif /* HAL_IPCC_MODULE_ENABLED */
#ifdef HAL_IRDA_MODULE_ENABLED
#include "stm32wlxx_hal_irda.h"
#endif /* HAL_IRDA_MODULE_ENABLED */
#ifdef HAL_IWDG_MODULE_ENABLED
#include "stm32wlxx_hal_iwdg.h"
#endif /* HAL_IWDG_MODULE_ENABLED */
#ifdef HAL_LPTIM_MODULE_ENABLED
#include "stm32wlxx_hal_lptim.h"
#endif /* HAL_LPTIM_MODULE_ENABLED */
#ifdef HAL_PKA_MODULE_ENABLED
#include "stm32wlxx_hal_pka.h"
#endif /* HAL_PKA_MODULE_ENABLED */
#ifdef HAL_PWR_MODULE_ENABLED
#include "stm32wlxx_hal_pwr.h"
#endif /* HAL_PWR_MODULE_ENABLED */
#ifdef HAL_RCC_MODULE_ENABLED
#include "stm32wlxx_hal_rcc.h"
#endif /* HAL_RCC_MODULE_ENABLED */
#ifdef HAL_RNG_MODULE_ENABLED
#include "stm32wlxx_hal_rng.h"
#endif /* HAL_RNG_MODULE_ENABLED */
#ifdef HAL_RTC_MODULE_ENABLED
#include "stm32wlxx_hal_rtc.h"
#endif /* HAL_RTC_MODULE_ENABLED */
#ifdef HAL_SMARTCARD_MODULE_ENABLED
#include "stm32wlxx_hal_smartcard.h"
#endif /* HAL_SMARTCARD_MODULE_ENABLED */
#ifdef HAL_SMBUS_MODULE_ENABLED
#include "stm32wlxx_hal_smbus.h"
#endif /* HAL_SMBUS_MODULE_ENABLED */
#ifdef HAL_SPI_MODULE_ENABLED
#include "stm32wlxx_hal_spi.h"
#endif /* HAL_SPI_MODULE_ENABLED */
#ifdef HAL_SUBGHZ_MODULE_ENABLED
#include "stm32wlxx_hal_subghz.h"
#endif /* HAL_SUBGHZ_MODULE_ENABLED */
#ifdef HAL_TIM_MODULE_ENABLED
#include "stm32wlxx_hal_tim.h"
#endif /* HAL_TIM_MODULE_ENABLED */
#ifdef HAL_UART_MODULE_ENABLED
#include "stm32wlxx_hal_uart.h"
#endif /* HAL_UART_MODULE_ENABLED */
#ifdef HAL_USART_MODULE_ENABLED
#include "stm32wlxx_hal_usart.h"
#endif /* HAL_USART_MODULE_ENABLED */
#ifdef HAL_WWDG_MODULE_ENABLED
#include "stm32wlxx_hal_wwdg.h"
#endif /* HAL_WWDG_MODULE_ENABLED */
/* Exported macro ------------------------------------------------------------*/
#ifdef USE_FULL_ASSERT
/**
* @brief The assert_param macro is used for function's parameters check.
* @param expr If expr is false, it calls assert_failed function
* which reports the name of the source file and the source
* line number of the call that failed.
* If expr is true, it returns no value.
* @retval None
*/
#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
/* Exported functions ------------------------------------------------------- */
void assert_failed(uint8_t* file, uint32_t line);
#else
#define assert_param(expr) ((void)0U)
#endif /* USE_FULL_ASSERT */
#ifdef __cplusplus
}
#endif
#endif /* STM32WLxx_HAL_CONF_H */