130 lines
5.4 KiB
Plaintext
130 lines
5.4 KiB
Plaintext
/**
|
|
@page TIM_OCActive TIM_OCActive example
|
|
|
|
@verbatim
|
|
******************************************************************************
|
|
* @file TIM/TIM_OCActive/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief This example shows how to configure the Timer to generate four
|
|
* delayed signals.
|
|
******************************************************************************
|
|
*
|
|
* Copyright (c) 2020 STMicroelectronics. All rights reserved.
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Configuration of the TIM peripheral in Output Compare Active mode
|
|
(when the counter matches the capture/compare register, the corresponding output
|
|
pin is set to its active state).
|
|
|
|
The TIM1 frequency is set to SystemCoreClock, and the objective is
|
|
to get TIM1 counter clock at 10 kHz so the Prescaler is computed as following:
|
|
- Prescaler = (TIM1CLK /TIM1 counter clock) - 1
|
|
|
|
SystemCoreClock is set to 48 MHz for STM32WLxx Devices.
|
|
|
|
The TIM1 CCR1 register value is equal to 10000:
|
|
TIM1_CH1 delay = CCR1_Val/TIM1 counter clock = 1s
|
|
so the TIM1 Channel 1 generates a signal with a delay equal to 1s.
|
|
|
|
The TIM1 CCR2 register value is equal to 5000:
|
|
TIM1_CH2 delay = CCR2_Val/TIM1 counter clock = 500 ms
|
|
so the TIM1 Channel 2 generates a signal with a delay equal to 500 ms.
|
|
|
|
The TIM1 CCR3 register value is equal to 2500:
|
|
TIM1_CH3 delay = CCR3_Val/TIM1 counter clock = 250 ms
|
|
so the TIM1 Channel 3 generates a signal with a delay equal to 250 ms.
|
|
|
|
The TIM1 CCR4 register value is equal to 1250:
|
|
TIM1_CH4 delay = CCR4_Val/TIM1 counter clock = 125 ms
|
|
so the TIM1 Channel 4 generates a signal with a delay equal to 125 ms.
|
|
|
|
The delay correspond to the time difference between PB15 rising edge and
|
|
TIM1_CHx signal rising edges.
|
|
STM32 board LED can be used to monitor the example status:
|
|
- LED1 turns ON if example is OK.
|
|
- LED3 toggles slowly in case of error.
|
|
|
|
@note Delay values mentioned above are theoretical (obtained when the system clock frequency
|
|
is exactly 48 MHz). Since the generated system clock frequency may vary from one board to another observed
|
|
delay might be slightly different.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note This example needs to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
Timer, Output, Compare, Active, Signals,
|
|
|
|
@par Directory contents
|
|
|
|
- TIM/TIM_OCActive/Inc/stm32wlxx_nucleo_conf.h BSP configuration file
|
|
- TIM/TIM_OCActive/Inc/stm32wlxx_hal_conf.h HAL configuration file
|
|
- TIM/TIM_OCActive/Inc/stm32wlxx_it.h Interrupt handlers header file
|
|
- TIM/TIM_OCActive/Inc/main.h Header for main.c module
|
|
- TIM/TIM_OCActive/Src/stm32wlxx_it.c Interrupt handlers
|
|
- TIM/TIM_OCActive/Src/main.c Main program
|
|
- TIM/TIM_OCActive/Src/stm32wlxx_hal_msp.c HAL MSP file
|
|
- TIM/TIM_OCActive/Src/system_stm32wlxx.c STM32WLxx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32WL55JCIx devices.
|
|
|
|
- This example has been tested with STMicroelectronics NUCLEO-WL55JC RevC
|
|
board and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
- NUCLEO-WL55JC RevC Set-up
|
|
Connect the following pins to an oscilloscope to monitor the different waveforms:
|
|
- Use LED1 connected to PB15 (Reference) (pin 28 in CN10 connector)
|
|
- PA8: (TIM1_CH1) (pin 16 in CN10 connector)
|
|
- PA9: (TIM1_CH2) (pin 19 in CN10 connector)
|
|
- PA10: (TIM1_CH3) (pin 32 in CN7 connector)
|
|
- PA11: (TIM1_CH4) (pin 5 in CN10 connector)
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
You should see these waveforms on oscilloscope :
|
|
|
|
CH1 ________________
|
|
_______________________________________________________________|
|
|
<---------------------- 1sec------------------------->
|
|
|
|
CH2 __________________________________________
|
|
______________________________________|
|
|
<------------500ms--------->
|
|
|
|
CH3 _____________________________________________________
|
|
___________________________|
|
|
<----250ms------->
|
|
|
|
CH4 ____________________________________________________________
|
|
_____________________|
|
|
<--125ms--->
|
|
|
|
LED ______________________________________________________________________
|
|
__________|
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|