/**
@page TIM_OnePulse_Init TIM example
@verbatim
******************************************************************************
* @file Examples_LL/TIM/TIM_OnePulse_Init/readme.txt
* @author MCD Application Team
* @brief Description of the TIM_OnePulse_Init example.
******************************************************************************
*
* Copyright (c) 2020 STMicroelectronics. All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
@endverbatim
@par Example Description
Configuration of a timer to generate a positive pulse in
Output Compare mode with a length of tPULSE and after a delay of tDELAY. This example
is based on the STM32WLxx TIM LL API. The peripheral initialization uses
LL initialization function to demonstrate LL Init.
The pulse is generated on OC1.
This example uses 2 timer instances:
- TIM1 generates a positive pulse of 50 us after a delay of 50 us. User push-button
is used to start TIM1 counter.
___
| |
User push-button ________________________| |________________________________
___________
| |
OC1 ______________________________________| |________
(TIM1_CH1) <---50 us---><---50 us--->
| |_ uwMeasuredPulseLength
|_ uwMeasuredDelay
TIM1_CH1 delay and pulse length are measured every time a pulse is generated.
Both can be observed through the debugger by monitoring the variables uwMeasuredDelay and
uwMeasuredPulseLength respectively.
- TIM2 generates a positive pulse of 3 s after a delay of 2 s. TIM2 counter start
is controlled through the slave mode controller. TI2FP2 signals is selected as
trigger input meaning that TIM2 counter starts when a rising edge is detected on
TI2FP2.
___
| |
TI2 _________________________| |_________________________________________
(TIM2_CH2)
___________________________
| |
OC1 ______________________________________| |____
(TIM2_CH1) <-----2s-----><----------3 s------------->
Both TIM1 and TIM2 are configured to generate a single pulse (timer counter
stops automatically at the next update event (UEV).
Connecting TIM1 OC1 to TIM2 TI2 allows to trigger TIM2 counter by pressing
the User push-button.
@par Keywords
Timers, Output, signals, One Pulse, PWM, Oscilloscope, External signal, Autoreload, Waveform
@par Directory contents
- TIM/TIM_OnePulse_Init/Inc/stm32wlxx_it.h Interrupt handlers header file
- TIM/TIM_OnePulse_Init/Inc/main.h Header for main.c module
- TIM/TIM_OnePulse_Init/Inc/stm32_assert.h Template file to include assert_failed function
- TIM/TIM_OnePulse_Init/Src/stm32wlxx_it.c Interrupt handlers
- TIM/TIM_OnePulse_Init/Src/main.c Main program
- TIM/TIM_OnePulse_Init/Src/system_stm32wlxx.c STM32WLxx system source file
@par Hardware and Software environment
- This example runs on STM32WL55JCIx devices.
- This example has been tested with NUCLEO-WL55JC RevC board and can be
easily tailored to any other supported device and development board.
- NUCLEO-WL55JC RevC Set-up:
- TIM1_CH1 PA.08: connected to pin 16 of CN10 connector
- TIM2_CH1 PA.05: connected to pin 11 of CN10 connector
- TIM2_CH2 PA.01: connected to pin 36 of CN10 connector
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
*/
6d27fec2e5