/**
@page RTC_TimeStamp RTC time stamp Example
@verbatim
******************************************************************************
* @file RTC/RTC_TimeStamp/readme.txt
* @author MCD Application Team
* @brief Description of the RTC time stamp example.
******************************************************************************
*
* Copyright (c) 2020 STMicroelectronics. All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
@endverbatim
@par Example Description
Configuration of the RTC HAL API to demonstrate the timestamp feature.
At the beginning of the main program the HAL_Init() function is called to reset
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system
clock (SYSCLK) to run at 0.
The RTC peripheral configuration is ensured by the HAL_RTC_Init() function.
This later is calling the HAL_RTC_MspInit()function which core is implementing
the configuration of the needed RTC resources according to the used hardware (CLOCK,
PWR, RTC clock source and BackUp). You may update this function to change RTC configuration.
@note LSI oscillator clock is used as RTC clock source by default.
The user can use also LSE as RTC clock source.
- The user uncomment the adequate line on the main.c file.
@code
#define RTC_CLOCK_SOURCE_LSI
/* #define RTC_CLOCK_SOURCE_LSE */
@endcode
- Open the ioc file with STM32CubeMX and select :
LSE as "Crystal/Ceramic Resonator" in RCC configuration.
LSE as RTC clock source in Clock configuration.
- Generate code
LSI oscillator clock is delivered by a 32 kHz RC.
LSE (when available on board) is delivered by a 32.768 kHz crystal.
HAL_RTCEx_SetTimeStamp_IT()function is then called to initialize the time stamp feature
with interrupt mode. It configures the time stamp pin to be rising edge and enables
the time stamp detection on time stamp pin.
HAL_RTC_SetTime()and HAL_RTC_SetDate() functions are then called to initialize the
time and the date.
The associated firmware performs the following:
1. After startup the program configure the RTC (Time date) and enable the feature
timeStamp.
2. On this board, time stamp pin (PC.13) is not connected to User push-button B1 (pin PA.00).
Therefore, an external connection is needed: connect PC.13 (CN7, pin 23) to voltage level 3.3V or you can simply pass your finger on PC.13 pin :
a time stamp event is detected and the calendar is saved in the time stamp structures.
Each time the user presses on the User push-button (B1), the current time and date are updated and displayed
on the debugger in aShowTime and aShowDate variables .
The current time and date stamp are updated and displayed on the debugger in aShowDateStamp and aShowTimeStamp variables .
- LED3 is toggling : This indicates that the system generates an error.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Keywords
RTC, Timer, Timestamp, Counter, LSE, LSI, Current time, Real Time Clock
@par Directory contents
- RTC/RTC_TimeStamp/Inc/stm32wlxx_nucleo_conf.h BSP configuration file
- RTC/RTC_TimeStamp/Inc/stm32wlxx_hal_conf.h HAL configuration file
- RTC/RTC_TimeStamp/Inc/stm32wlxx_it.h Interrupt handlers header file
- RTC/RTC_TimeStamp/Inc/main.h Header for main.c module
- RTC/RTC_TimeStamp/Src/stm32wlxx_it.c Interrupt handlers
- RTC/RTC_TimeStamp/Src/main.c Main program
- RTC/RTC_TimeStamp/Src/stm32wlxx_hal_msp.c HAL MSP module
- RTC/RTC_TimeStamp/Src/system_stm32wlxx.c STM32WLxx system source file
@par Hardware and Software environment
- This example runs on STM32WL55JCIx devices.
- This example has been tested with STMicroelectronics NUCLEO-WL55JC RevC
board and can be easily tailored to any other supported device
and development board.
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
*/
378e461e46