71 lines
2.6 KiB
Plaintext
71 lines
2.6 KiB
Plaintext
/**
|
|
@page EXTI_ToggleLedOnIT_Init EXTI example
|
|
|
|
@verbatim
|
|
******************************************************************************
|
|
* @file Examples_LL/EXTI/EXTI_ToggleLedOnIT_Init/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the EXTI example.
|
|
******************************************************************************
|
|
*
|
|
* Copyright (c) 2020 STMicroelectronics. All rights reserved.
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example describes how to configure the EXTI and use
|
|
GPIOs to toggle the user LEDs available on the board when
|
|
a user button is pressed. This example is based on the
|
|
STM32WLxx LL API. Peripheral initialization is done using LL
|
|
initialization function to demonstrate LL init usage.
|
|
|
|
In this example, one EXTI line (External line 0) is configured to generate
|
|
an interrupt on each falling edge.
|
|
|
|
In the interrupt routine a led connected to a specific GPIO pin is toggled.
|
|
|
|
In this example:
|
|
- External line 0 is connected to PA.00 pin
|
|
- when falling edge is detected on External line 0 by pressing User push-button (B1), LED2 toggles
|
|
|
|
On NUCLEO-WL55JC RevC:
|
|
- External line 0 is connected to User push-button (B1)
|
|
|
|
@par Keywords
|
|
|
|
System, GPIO, Output, Alternate function, EXTI, Toggle
|
|
|
|
|
|
@par Directory contents
|
|
|
|
- EXTI/EXTI_ToggleLedOnIT_Init/Inc/stm32wlxx_it.h Interrupt handlers header file
|
|
- EXTI/EXTI_ToggleLedOnIT_Init/Inc/main.h Header for main.c module
|
|
- EXTI/EXTI_ToggleLedOnIT_Init/Inc/stm32_assert.h Template file to include assert_failed function
|
|
- EXTI/EXTI_ToggleLedOnIT_Init/Src/stm32wlxx_it.c Interrupt handlers
|
|
- EXTI/EXTI_ToggleLedOnIT_Init/Src/main.c Main program
|
|
- EXTI/EXTI_ToggleLedOnIT_Init/Src/system_stm32wlxx.c STM32WLxx system source file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32WL55JCIx devices.
|
|
|
|
- This example has been tested with NUCLEO-WL55JC RevC board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|