104 lines
4.4 KiB
Plaintext
104 lines
4.4 KiB
Plaintext
/**
|
|
@page TIM_OnePulse_Init TIM example
|
|
|
|
@verbatim
|
|
******************************************************************************
|
|
* @file Examples_LL/TIM/TIM_OnePulse_Init/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the TIM_OnePulse_Init example.
|
|
******************************************************************************
|
|
*
|
|
* Copyright (c) 2020 STMicroelectronics. All rights reserved.
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Configuration of a timer to generate a positive pulse in
|
|
Output Compare mode with a length of tPULSE and after a delay of tDELAY. This example
|
|
is based on the STM32WLxx TIM LL API. The peripheral initialization uses
|
|
LL initialization function to demonstrate LL Init.
|
|
|
|
The pulse is generated on OC1.
|
|
|
|
This example uses 2 timer instances:
|
|
|
|
- TIM1 generates a positive pulse of 50 us after a delay of 50 us. User push-button
|
|
is used to start TIM1 counter.
|
|
___
|
|
| |
|
|
User push-button ________________________| |________________________________
|
|
___________
|
|
| |
|
|
OC1 ______________________________________| |________
|
|
(TIM1_CH1) <---50 us---><---50 us--->
|
|
| |_ uwMeasuredPulseLength
|
|
|_ uwMeasuredDelay
|
|
|
|
TIM1_CH1 delay and pulse length are measured every time a pulse is generated.
|
|
Both can be observed through the debugger by monitoring the variables uwMeasuredDelay and
|
|
uwMeasuredPulseLength respectively.
|
|
|
|
- TIM2 generates a positive pulse of 3 s after a delay of 2 s. TIM2 counter start
|
|
is controlled through the slave mode controller. TI2FP2 signals is selected as
|
|
trigger input meaning that TIM2 counter starts when a rising edge is detected on
|
|
TI2FP2.
|
|
___
|
|
| |
|
|
TI2 _________________________| |_________________________________________
|
|
(TIM2_CH2)
|
|
___________________________
|
|
| |
|
|
OC1 ______________________________________| |____
|
|
(TIM2_CH1) <-----2s-----><----------3 s------------->
|
|
|
|
|
|
|
|
Both TIM1 and TIM2 are configured to generate a single pulse (timer counter
|
|
stops automatically at the next update event (UEV).
|
|
|
|
Connecting TIM1 OC1 to TIM2 TI2 allows to trigger TIM2 counter by pressing
|
|
the User push-button.
|
|
|
|
@par Keywords
|
|
|
|
Timers, Output, signals, One Pulse, PWM, Oscilloscope, External signal, Autoreload, Waveform
|
|
|
|
@par Directory contents
|
|
|
|
- TIM/TIM_OnePulse_Init/Inc/stm32wlxx_it.h Interrupt handlers header file
|
|
- TIM/TIM_OnePulse_Init/Inc/main.h Header for main.c module
|
|
- TIM/TIM_OnePulse_Init/Inc/stm32_assert.h Template file to include assert_failed function
|
|
- TIM/TIM_OnePulse_Init/Src/stm32wlxx_it.c Interrupt handlers
|
|
- TIM/TIM_OnePulse_Init/Src/main.c Main program
|
|
- TIM/TIM_OnePulse_Init/Src/system_stm32wlxx.c STM32WLxx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32WL55JCIx devices.
|
|
|
|
- This example has been tested with NUCLEO-WL55JC RevC board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- NUCLEO-WL55JC RevC Set-up:
|
|
- TIM1_CH1 PA.08: connected to pin 16 of CN10 connector
|
|
- TIM2_CH1 PA.05: connected to pin 11 of CN10 connector
|
|
- TIM2_CH2 PA.01: connected to pin 36 of CN10 connector
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|