revised SPI and LCD control port
This commit is contained in:
parent
746671f565
commit
c196b9593d
|
|
@ -89,19 +89,21 @@ void Error_Handler(void);
|
|||
#define VOLTAGE_DETECT_GPIO_Port GPIOA
|
||||
|
||||
//SPI1 ST7789
|
||||
#define LCD_CS_Pin GPIO_PIN_4 //ST7789, Pin-7
|
||||
#define LCD_CS_GPIO_Port GPIOA
|
||||
|
||||
#define LCD_RES_Pin GPIO_PIN_3 //ST7789, Pin-5
|
||||
#define LCD_RES_GPIO_Port GPIOB
|
||||
#define BLK_Pin GPIO_PIN_8 //ST7789, Pin-8
|
||||
#define BLK_GPIO_Port GPIOB
|
||||
|
||||
#define LCD_BLK_Pin GPIO_PIN_8 //ST7789, Pin-8
|
||||
#define LCD_BLK_GPIO_Port GPIOB
|
||||
|
||||
#define LCD_CS_Pin GPIO_PIN_10 //ST7789, Pin-7
|
||||
#define LCD_CS_GPIO_Port GPIOB
|
||||
|
||||
#define LCD_DC_Pin GPIO_PIN_5 //ST7789, Pin-6
|
||||
#define LCD_DC_GPIO_Port GPIOB
|
||||
|
||||
#define LCD_TE_Pin GPIO_PIN_13
|
||||
#define LCD_TE_GPIO_Port GPIOB
|
||||
|
||||
#define LCD_DC_Pin GPIO_PIN_5 //ST7789, Pin-6
|
||||
#define LCD_DC_GPIO_Port GPIOB
|
||||
|
||||
#define KEY1_Pin GPIO_PIN_0
|
||||
#define KEY1_GPIO_Port GPIOA
|
||||
|
|
|
|||
|
|
@ -44,13 +44,14 @@ void MX_DMA_Init(void)
|
|||
__HAL_RCC_DMA1_CLK_ENABLE();
|
||||
|
||||
/* DMA interrupt init */
|
||||
#if 1
|
||||
/* DMA1_Channel2_IRQn interrupt configuration */
|
||||
HAL_NVIC_SetPriority(DMA1_Channel2_IRQn, 0, 0);
|
||||
HAL_NVIC_EnableIRQ(DMA1_Channel2_IRQn);
|
||||
/* DMA1_Channel3_IRQn interrupt configuration */
|
||||
HAL_NVIC_SetPriority(DMA1_Channel3_IRQn, 0, 0);
|
||||
HAL_NVIC_EnableIRQ(DMA1_Channel3_IRQn);
|
||||
|
||||
#endif
|
||||
/* DMA1_Channel5_IRQn interrupt configuration */
|
||||
HAL_NVIC_SetPriority(DMA1_Channel5_IRQn, 2, 0);
|
||||
HAL_NVIC_EnableIRQ(DMA1_Channel5_IRQn);
|
||||
|
|
|
|||
|
|
@ -54,10 +54,15 @@ void MX_GPIO_Init(void)
|
|||
|LED3_Pin, GPIO_PIN_RESET);
|
||||
|
||||
/*Configure GPIO pin Output Level */
|
||||
HAL_GPIO_WritePin(GPIOA, LCD_CS_Pin|LCD_RES_Pin|W25Q_CS_Pin, GPIO_PIN_RESET);
|
||||
//HAL_GPIO_WritePin(GPIOA, LCD_CS_Pin|LCD_RES_Pin|W25Q_CS_Pin, GPIO_PIN_RESET);
|
||||
HAL_GPIO_WritePin(LCD_RES_GPIO_Port, LCD_RES_Pin, GPIO_PIN_SET);
|
||||
|
||||
HAL_GPIO_WritePin(LCD_BLK_GPIO_Port, LCD_BLK_Pin, GPIO_PIN_RESET);
|
||||
HAL_GPIO_WritePin(LCD_CS_GPIO_Port, LCD_CS_Pin, GPIO_PIN_RESET);
|
||||
HAL_GPIO_WritePin(LCD_DC_GPIO_Port, LCD_DC_Pin, GPIO_PIN_RESET);
|
||||
|
||||
/*Configure GPIO pin Output Level */
|
||||
HAL_GPIO_WritePin(GPIOB, LCD_TE_Pin|LCD_DC_Pin|LED_Pin, GPIO_PIN_RESET);
|
||||
//HAL_GPIO_WritePin(GPIOB, LCD_TE_Pin|LCD_DC_Pin|LED_Pin, GPIO_PIN_RESET);
|
||||
|
||||
/*Configure GPIO pins : PBPin PBPin PBPin */
|
||||
GPIO_InitStruct.Pin = LED1_Pin|LED2_Pin|LED3_Pin;
|
||||
|
|
@ -86,14 +91,14 @@ void MX_GPIO_Init(void)
|
|||
HAL_GPIO_Init(BUT3_GPIO_Port, &GPIO_InitStruct);
|
||||
|
||||
/*Configure GPIO pins : PAPin PAPin PAPin */
|
||||
GPIO_InitStruct.Pin = LCD_CS_Pin|LCD_RES_Pin|W25Q_CS_Pin;
|
||||
GPIO_InitStruct.Pin = LCD_CS_Pin;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
||||
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
||||
HAL_GPIO_Init(LCD_CS_GPIO_Port, &GPIO_InitStruct);
|
||||
|
||||
/*Configure GPIO pins : PBPin PBPin PBPin */
|
||||
GPIO_InitStruct.Pin = LCD_TE_Pin|LCD_DC_Pin|LED_Pin;
|
||||
GPIO_InitStruct.Pin = LCD_RES_Pin|LCD_BLK_Pin|LCD_DC_Pin;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
||||
|
|
|
|||
|
|
@ -81,7 +81,7 @@ MENU my_menu={
|
|||
{"screenshot","saving ","success ","fail "},
|
||||
0
|
||||
};
|
||||
uint8_t key1_press,key2_press,button_press;
|
||||
uint8_t key1_press,key2_press,button_press=1;
|
||||
//menu1 bin_size or resize
|
||||
//menu2 color_method
|
||||
//menu3 screenshot
|
||||
|
|
@ -119,13 +119,26 @@ int main(void)
|
|||
MX_LoRaWAN_Init();
|
||||
/* USER CODE BEGIN 2 */
|
||||
//MX_ADC_Init();
|
||||
MX_DMA_Init();
|
||||
MX_I2C_Init();
|
||||
MX_SPI_Init();
|
||||
MX_I2C_Init();
|
||||
|
||||
MX_DMA_Init();
|
||||
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"\r\n Start LCD test...........");
|
||||
|
||||
//HAL_TIM_PWM_Start(&htim3,TIM_CHANNEL_1);
|
||||
|
||||
ST7789_Init();
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"\r\n Set Black Light...on....");
|
||||
ST7789_SetBackLight(1);
|
||||
HAL_Delay(500);
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"\r\n Set Black Light... off....");
|
||||
ST7789_SetBackLight(0);
|
||||
HAL_Delay(500);
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"\r\n Set Black Light...on....");
|
||||
ST7789_SetBackLight(1);
|
||||
|
||||
// HAL_Delay(500);
|
||||
// ST7789_Test();
|
||||
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"\r\n END LCD test...........");
|
||||
|
|
@ -139,7 +152,7 @@ int main(void)
|
|||
mlx90640_init(FPS2HZ,&mlx90640);
|
||||
HAL_Delay(500);
|
||||
mlx90640_get_temp_mat(&mlx90640,mlx90640To);
|
||||
ST7789_SetBackLight(50);
|
||||
ST7789_SetBackLight(0);
|
||||
draw_spectrum(img_method_arr[my_menu.chose_color_method_index]);
|
||||
|
||||
|
||||
|
|
@ -149,7 +162,6 @@ int main(void)
|
|||
|
||||
/* USER CODE BEGIN 3 */
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"\r\nL menu selected:%d,%d,%d\n",chose_menu_index,key1_press,key2_press);
|
||||
APP_LOG(TS_OFF,VLEVEL_M,"\r\nM menu selected:%d,%d,%d\n",chose_menu_index,key1_press,key2_press);
|
||||
|
||||
if(key1_press==1)
|
||||
chose_menu_index--;
|
||||
|
|
@ -160,6 +172,8 @@ int main(void)
|
|||
if(chose_menu_index>3)
|
||||
chose_menu_index=1;
|
||||
#if 1
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"\r\nGet Raw data \r\n");
|
||||
|
||||
mlx90640_get_temp_mat(&mlx90640,mlx90640To);
|
||||
char buf[128];
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"\r\n");
|
||||
|
|
@ -177,6 +191,8 @@ int main(void)
|
|||
{//温度异常重新获取
|
||||
mlx90640_get_temp_mat(&mlx90640,mlx90640To);
|
||||
}
|
||||
sprintf(buf,"\r\nMax=%.2f, Min=%.2f, Center=%.2f\r\n",(float)max_temp, (float)min_temp, (float)mlx90640To[768/2]);
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"%s", buf);
|
||||
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"\r\n");
|
||||
for (int i=0; i< 24; i++) {
|
||||
|
|
@ -190,6 +206,7 @@ int main(void)
|
|||
}
|
||||
center_temp=mlx90640To[768/2];
|
||||
#endif
|
||||
#if 0
|
||||
if(button_press)
|
||||
my_menu.screenshot_index=1;
|
||||
ST7789_WriteString(0,0,my_menu.voltage_info,Font_7x10,WHITE,BLACK);
|
||||
|
|
@ -231,9 +248,10 @@ int main(void)
|
|||
else
|
||||
Besize_draw(bmp8,img_method_arr[my_menu.chose_color_method_index],notsavefile);
|
||||
}
|
||||
HAL_GPIO_TogglePin(GPIOB,GPIO_PIN_5);
|
||||
chose_menu_index ++;
|
||||
//HAL_GPIO_TogglePin(GPIOB,GPIO_PIN_5);
|
||||
// UART_printf(&huart1,"%d,%d,%d\n",chose_menu_index,key1_press,key2_press);
|
||||
|
||||
#endif
|
||||
}
|
||||
/* USER CODE END 2 */
|
||||
|
||||
|
|
|
|||
|
|
@ -41,18 +41,18 @@ void MX_SPI_Init(void)
|
|||
/* USER CODE END SPI1_Init 1 */
|
||||
hspi1.Instance = SPI1;
|
||||
hspi1.Init.Mode = SPI_MODE_MASTER;
|
||||
hspi1.Init.Direction = SPI_DIRECTION_1LINE;//SPI_DIRECTION_2LINES;
|
||||
hspi1.Init.Direction = SPI_DIRECTION_2LINES;
|
||||
hspi1.Init.DataSize = SPI_DATASIZE_8BIT;
|
||||
hspi1.Init.CLKPolarity = SPI_POLARITY_HIGH;//SPI_POLARITY_LOW;
|
||||
hspi1.Init.CLKPolarity = SPI_POLARITY_LOW;
|
||||
hspi1.Init.CLKPhase = SPI_PHASE_1EDGE;
|
||||
hspi1.Init.NSS = SPI_NSS_SOFT;
|
||||
hspi1.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2; //SPI_BAUDRATEPRESCALER_64;
|
||||
hspi1.Init.FirstBit = SPI_FIRSTBIT_MSB;
|
||||
hspi1.Init.TIMode = SPI_TIMODE_DISABLE;
|
||||
hspi1.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
|
||||
hspi1.Init.CRCPolynomial = 10; //7;
|
||||
// hspi1.Init.CRCLength = SPI_CRC_LENGTH_DATASIZE;
|
||||
// hspi1.Init.NSSPMode = SPI_NSS_PULSE_ENABLE;
|
||||
hspi1.Init.CRCPolynomial = 7; //7;
|
||||
hspi1.Init.CRCLength = SPI_CRC_LENGTH_DATASIZE;
|
||||
hspi1.Init.NSSPMode = SPI_NSS_PULSE_ENABLE;
|
||||
if (HAL_SPI_Init(&hspi1) != HAL_OK)
|
||||
{
|
||||
Error_Handler();
|
||||
|
|
@ -89,7 +89,7 @@ void HAL_SPI_MspInit(SPI_HandleTypeDef* spiHandle)
|
|||
* PA6 SPI1_MISO
|
||||
* PA7 SPI1_MOSI
|
||||
*/
|
||||
GPIO_InitStruct.Pin = MEMS_SPI_MOSI_Pin; //MEMS_SPI_MOSI_Pin|MEMS_CS_N_Pin|MEMS_SPI_MISO_Pin;
|
||||
GPIO_InitStruct.Pin = MEMS_SPI_MOSI_Pin||MEMS_SPI_MISO_Pin; //MEMS_SPI_MOSI_Pin|MEMS_CS_N_Pin|MEMS_SPI_MISO_Pin;
|
||||
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
|
||||
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
|
||||
|
|
@ -102,7 +102,7 @@ void HAL_SPI_MspInit(SPI_HandleTypeDef* spiHandle)
|
|||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
|
||||
GPIO_InitStruct.Alternate = GPIO_AF5_SPI1;
|
||||
HAL_GPIO_Init(MEMS_SPI_SCK_GPIO_Port, &GPIO_InitStruct);
|
||||
|
||||
#if 1
|
||||
/* SPI1 DMA Init */
|
||||
/* SPI1_RX Init */
|
||||
hdma_spi1_rx.Instance = DMA1_Channel2;
|
||||
|
|
@ -152,7 +152,7 @@ void HAL_SPI_MspInit(SPI_HandleTypeDef* spiHandle)
|
|||
HAL_NVIC_SetPriority(SPI1_IRQn, 0, 0);
|
||||
HAL_NVIC_EnableIRQ(SPI1_IRQn);
|
||||
/* USER CODE BEGIN SPI1_MspInit 1 */
|
||||
|
||||
#endif
|
||||
/* USER CODE END SPI1_MspInit 1 */
|
||||
}
|
||||
}
|
||||
|
|
@ -174,14 +174,14 @@ void HAL_SPI_MspDeInit(SPI_HandleTypeDef* spiHandle)
|
|||
* PA6 SPI1_MISO
|
||||
* PA7 SPI1_MOSI
|
||||
*/
|
||||
HAL_GPIO_DeInit(GPIOA, MEMS_SPI_MOSI_Pin|MEMS_CS_N_Pin|MEMS_SPI_MISO_Pin);
|
||||
HAL_GPIO_DeInit(MEMS_SPI_MOSI_GPIO_Port, MEMS_SPI_MOSI_Pin|MEMS_SPI_MISO_Pin);
|
||||
|
||||
HAL_GPIO_DeInit(MEMS_SPI_SCK_GPIO_Port, MEMS_SPI_SCK_Pin);
|
||||
|
||||
#if 0
|
||||
/* SPI1 DMA DeInit */
|
||||
HAL_DMA_DeInit(spiHandle->hdmarx);
|
||||
HAL_DMA_DeInit(spiHandle->hdmatx);
|
||||
|
||||
#endif
|
||||
/* SPI1 interrupt Deinit */
|
||||
HAL_NVIC_DisableIRQ(SPI1_IRQn);
|
||||
/* USER CODE BEGIN SPI1_MspDeInit 1 */
|
||||
|
|
|
|||
|
|
@ -624,6 +624,12 @@ void ST7789_DrawFilledCircle(int16_t x0, int16_t y0, int16_t r, uint16_t color)
|
|||
void ST7789_SetBackLight(uint8_t blk)
|
||||
{
|
||||
//BLK_TIM=blk;
|
||||
//ST7789_BLK_Clr();
|
||||
if (blk) {
|
||||
ST7789_BLK_Set();
|
||||
} else {
|
||||
ST7789_BLK_Clr();
|
||||
}
|
||||
}
|
||||
/**
|
||||
* @brief Open/Close tearing effect line
|
||||
|
|
@ -645,11 +651,11 @@ void ST7789_TearEffect(uint8_t tear)
|
|||
*/
|
||||
void ST7789_Test(void)
|
||||
{
|
||||
ST7789_Fill_Color(BLACK);
|
||||
HAL_Delay(1000);
|
||||
ST7789_Fill_Color(BLUE);
|
||||
HAL_Delay(2000);
|
||||
ST7789_WriteString(10, 20, "Speed Test", Font_11x18, RED, BLACK);
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"\r\n Speed Test...........");
|
||||
HAL_Delay(1000);
|
||||
HAL_Delay(100);
|
||||
ST7789_Fill_Color(CYAN);
|
||||
ST7789_Fill_Color(RED);
|
||||
ST7789_Fill_Color(BLUE);
|
||||
|
|
@ -669,38 +675,38 @@ void ST7789_Test(void)
|
|||
ST7789_WriteString(10, 50, "Hello World!", Font_7x10, RED, BLACK);
|
||||
ST7789_WriteString(10, 75, "Hello World!", Font_11x18, YELLOW, BLACK);
|
||||
ST7789_WriteString(10, 100, "Hello World!", Font_16x26, MAGENTA, BLACK);
|
||||
HAL_Delay(1000);
|
||||
HAL_Delay(100);
|
||||
|
||||
APP_LOG(TS_OFF,VLEVEL_L,"\r\n Rect, circle Triangle test...........");
|
||||
ST7789_Fill_Color(BLACK);
|
||||
ST7789_WriteString(10, 10, "Rect./Line.", Font_11x18, YELLOW, BLACK);
|
||||
ST7789_DrawRectangle(40, 40, 200, 200, WHITE);
|
||||
HAL_Delay(1000);
|
||||
HAL_Delay(100);
|
||||
|
||||
ST7789_Fill_Color(BLACK);
|
||||
ST7789_WriteString(10, 10, "Filled Rect.", Font_11x18, YELLOW, BLACK);
|
||||
ST7789_DrawFilledRectangle(40, 40, 160, 160, WHITE);
|
||||
HAL_Delay(1000);
|
||||
HAL_Delay(100);
|
||||
|
||||
ST7789_Fill_Color(BLACK);
|
||||
ST7789_WriteString(10, 10, "Circle.", Font_11x18, YELLOW, BLACK);
|
||||
ST7789_DrawCircle(120, 120, 60, WHITE);
|
||||
HAL_Delay(1000);
|
||||
HAL_Delay(100);
|
||||
|
||||
ST7789_Fill_Color(BLACK);
|
||||
ST7789_WriteString(10, 10, "Filled Cir.", Font_11x18, YELLOW, BLACK);
|
||||
ST7789_DrawFilledCircle(120, 120, 60, WHITE);
|
||||
HAL_Delay(1000);
|
||||
HAL_Delay(100);
|
||||
|
||||
ST7789_Fill_Color(BLACK);
|
||||
ST7789_WriteString(10, 10, "Triangle", Font_11x18, YELLOW, BLACK);
|
||||
ST7789_DrawTriangle(30, 30, 30, 70, 60, 40, WHITE);
|
||||
HAL_Delay(1000);
|
||||
HAL_Delay(100);
|
||||
|
||||
ST7789_Fill_Color(BLACK);
|
||||
ST7789_WriteString(10, 10, "Filled Tri", Font_11x18, YELLOW, BLACK);
|
||||
ST7789_DrawFilledTriangle(30, 30, 30, 70, 60, 40, WHITE);
|
||||
HAL_Delay(1000);
|
||||
HAL_Delay(100);
|
||||
|
||||
/*
|
||||
|
||||
|
|
|
|||
|
|
@ -15,16 +15,26 @@
|
|||
*/
|
||||
|
||||
/* Define the pins tp connect */
|
||||
#define ST7789_RST_PORT GPIOB
|
||||
#define ST7789_RST_PIN GPIO_PIN_3
|
||||
#define ST7789_DC_PORT GPIOB
|
||||
#define ST7789_DC_PIN GPIO_PIN_5
|
||||
//#define ST7789_RST_PORT GPIOB
|
||||
//#define ST7789_RST_PIN GPIO_PIN_3
|
||||
//#define ST7789_DC_PORT GPIOB
|
||||
//#define ST7789_DC_PIN GPIO_PIN_5
|
||||
|
||||
//#define ST7789_CS_PORT GPIOA
|
||||
//#define ST7789_CS_PIN GPIO_PIN_3
|
||||
|
||||
#define ST7789_CS_PORT MEMS_CS_N_GPIO_Port
|
||||
#define ST7789_CS_PIN MEMS_CS_N_Pin
|
||||
#define ST7789_RST_PORT LCD_RES_GPIO_Port
|
||||
#define ST7789_RST_PIN LCD_RES_Pin
|
||||
#define ST7789_DC_PORT LCD_DC_GPIO_Port
|
||||
#define ST7789_DC_PIN LCD_DC_Pin
|
||||
|
||||
|
||||
#define ST7789_BLK_PORT LCD_BLK_GPIO_Port
|
||||
#define ST7789_BLK_PIN LCD_BLK_Pin
|
||||
|
||||
#define ST7789_CS_PORT LCD_CS_GPIO_Port
|
||||
#define ST7789_CS_PIN LCD_CS_Pin
|
||||
|
||||
|
||||
/***** Use if need backlight control *****
|
||||
|
||||
|
|
@ -47,11 +57,12 @@
|
|||
/* Choose a type you are using */
|
||||
//#define USING_135X240
|
||||
//#define USING_240X240
|
||||
#define USING_320X240
|
||||
//#define USING_320X240
|
||||
#define USING_280X240
|
||||
|
||||
/* Choose a display rotation you want to use: (0-3) */
|
||||
//#define ST7789_ROTATION 0
|
||||
#define ST7789_ROTATION 1
|
||||
#define ST7789_ROTATION 0
|
||||
//#define ST7789_ROTATION 1
|
||||
//#define ST7789_ROTATION 2 // use Normally on 240x240
|
||||
//#define ST7789_ROTATION 3
|
||||
|
||||
|
|
@ -125,6 +136,26 @@
|
|||
#define Y_SHIFT 0
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#ifdef USING_280X240
|
||||
#define ST7789_WIDTH 280
|
||||
#define ST7789_HEIGHT 240
|
||||
|
||||
#if ST7789_ROTATION == 0
|
||||
#define X_SHIFT 0
|
||||
#define Y_SHIFT 0
|
||||
#elif ST7789_ROTATION == 1
|
||||
#define X_SHIFT 0
|
||||
#define Y_SHIFT 0
|
||||
#elif ST7789_ROTATION == 2
|
||||
#define X_SHIFT 0
|
||||
#define Y_SHIFT 0
|
||||
#elif ST7789_ROTATION == 3
|
||||
#define X_SHIFT 0
|
||||
#define Y_SHIFT 0
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
*Color of pen
|
||||
*If you want to use another color, you can choose one in RGB565 format.
|
||||
|
|
@ -216,6 +247,9 @@
|
|||
#define ST7789_DC_Clr() HAL_GPIO_WritePin(ST7789_DC_PORT, ST7789_DC_PIN, GPIO_PIN_RESET)
|
||||
#define ST7789_DC_Set() HAL_GPIO_WritePin(ST7789_DC_PORT, ST7789_DC_PIN, GPIO_PIN_SET)
|
||||
|
||||
#define ST7789_BLK_Clr() HAL_GPIO_WritePin(ST7789_BLK_PORT,ST7789_BLK_PIN,GPIO_PIN_RESET)
|
||||
#define ST7789_BLK_Set() HAL_GPIO_WritePin(ST7789_BLK_PORT,ST7789_BLK_PIN,GPIO_PIN_SET)
|
||||
|
||||
#ifdef ST7789_USE_CS
|
||||
#define ST7789_Select() HAL_GPIO_WritePin(ST7789_CS_PORT, ST7789_CS_PIN, GPIO_PIN_RESET)
|
||||
#define ST7789_UnSelect() HAL_GPIO_WritePin(ST7789_CS_PORT, ST7789_CS_PIN, GPIO_PIN_SET)
|
||||
|
|
@ -262,18 +296,22 @@ void ST7789_Test(void);
|
|||
#if !defined(USING_240X240)
|
||||
#if !defined(USING_135X240)
|
||||
#if !defined(USING_320X240)
|
||||
#if !defined(USING_280X240)
|
||||
#error You should at least choose one display resolution!
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if !defined(USING_135X240)
|
||||
#if !defined(USING_240X240)
|
||||
#if !defined(USING_320X240)
|
||||
#if !defined(USING_280X240)
|
||||
#error You should at least choose one display resolution!
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
||||
#ifndef ST7789_ROTATION
|
||||
|
|
|
|||
Loading…
Reference in New Issue