---updated correct radio firmware

Core/Inc/platform.h

@@ -7,7 +7,7 @@
   ******************************************************************************
   * @attention
   *
-  * Copyright (c) 2021 STMicroelectronics.
+  * Copyright (c) 2022 STMicroelectronics.
   * All rights reserved.
   *
   * This software is licensed under terms that can be found in the LICENSE file
@@ -28,7 +28,7 @@ extern "C" {
 
 /* Exported constants --------------------------------------------------------*/
 
-#define USE_BSP_DRIVER
+//#define USE_BSP_DRIVER
 /* USER CODE BEGIN EC */
 
 /* USER CODE END EC */
@@ -38,6 +38,7 @@ extern "C" {
 #include "stm32wlxx.h"
 #include "main.h"
 #include "stm32wlxx_ll_gpio.h"
+#define		YUNHORN_STS_WLE5CCxx
 #if defined(USE_BSP_DRIVER)
 /* code generated by STM32CubeMX does not support BSP.  */
 /* In order to use BSP, users can add the BSP files in the IDE project space */
@@ -47,6 +48,14 @@ extern "C" {
 #endif /* defined(USE_BSP_DRIVER) */
 
 /* USER CODE BEGIN include */
+#define PROB2_Pin GPIO_PIN_13
+#define PROB2_GPIO_Port GPIOB
+#define PROB1_Pin GPIO_PIN_12
+#define PROB1_GPIO_Port GPIOB
+#define PROBE_LINE2_PORT	GPIOB
+#define PROBE_LINE2_PIN		GPIO_PIN_13
+#define PROBE_LINE1_PORT	GPIOB
+#define PROBE_LINE1_PIN		GPIO_PIN_12
 
 /* USER CODE END include */
 

LoRaWAN/Target/radio_board_if.c

@@ -1,23 +1,21 @@
-/* USER CODE BEGIN Header */
 /**
  ******************************************************************************
  * @file    radio_board_if.c
-  * @author  MCD Application Team
+ * @author  YunHorn Technology Limited Application Team
  * @brief   This file provides an interface layer between MW and Radio Board
  ******************************************************************************
  * @attention
  *
-  * Copyright (c) 2021 STMicroelectronics.
+ * Copyright (c) 2023 YunHorn Technology Limited.
-  * All rights reserved.
+ * All rights reserved.</center></h2>
  *
-  * This software is licensed under terms that can be found in the LICENSE file
+ * This software component is licensed by ST under Ultimate Liberty license
-  * in the root directory of this software component.
+ * SLA0044, the "License"; You may not use this file except in compliance with
-  * If no LICENSE file comes with this software, it is provided AS-IS.
+ * the License. You may obtain a copy of the License at:
+ *                             www.st.com/SLA0044
  *
  ******************************************************************************
  */
-/* USER CODE END Header */
-
 /* Includes ------------------------------------------------------------------*/
 #include "radio_board_if.h"
 
@@ -62,24 +60,62 @@ int32_t RBI_Init(void)
 
   /* USER CODE END RBI_Init_1 */
 #if defined(USE_BSP_DRIVER)
-  /* Important note: BSP code is board dependent
+  /* code generated by MX does not support BSP */
-   * STM32WL_Nucleo code can be found
+  /* In order to use BSP driver, add the correspondent files in the IDE workspace */
-   *       either in STM32CubeWL package under Drivers/BSP/STM32WLxx_Nucleo/
+  /* and define USE_BSP_DRIVER in the preprocessor definitions  or in platform.h */
-   *       or at https://github.com/STMicroelectronics/STM32CubeWL/tree/main/Drivers/BSP/STM32WLxx_Nucleo/
-   * 1/ For User boards, the BSP/STM32WLxx_Nucleo/ directory can be copied and replaced in the project. The copy must then be updated depending:
-   *       on board RF switch configuration (pin control, number of port etc)
-   *       on TCXO configuration
-   *       on DC/DC configuration
-   *       on maximum output power that the board can deliver*/
   return BSP_RADIO_Init();
+#elif defined(YUNHORN_STS_WLE5CCxx)
+  /* should be calling BSP_RADIO_Init() but not supported by MX*/
+
+  GPIO_InitTypeDef  gpio_init_structure = {0};
+
+#if defined(YUNHORN_STS_RF_CHANNEL_SWITCH)
+    /* Enable the Radio Switch Clock */
+    RF_SW_CTRL1_GPIO_CLK_ENABLE();
+    RF_SW_CTRL2_GPIO_CLK_ENABLE();
+    /* Configure the Radio Switch pin */
+    gpio_init_structure.Pin   = RF_SW_CTRL1_PIN;
+    gpio_init_structure.Mode  = GPIO_MODE_OUTPUT_PP;
+    gpio_init_structure.Pull  = GPIO_NOPULL;
+    gpio_init_structure.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    HAL_GPIO_Init(RF_SW_CTRL1_GPIO_PORT, &gpio_init_structure);
+    gpio_init_structure.Pin = RF_SW_CTRL2_PIN;
+    HAL_GPIO_Init(RF_SW_CTRL2_GPIO_PORT, &gpio_init_structure);
+
+    HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_RESET);
+    HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_RESET);
+#else
+  /* Enable the Radio Switch Clock */
+  RF_SW_CTRL3_GPIO_CLK_ENABLE();
+
+  /* Configure the Radio Switch pin */
+  gpio_init_structure.Pin   = RF_SW_CTRL1_PIN;
+  gpio_init_structure.Mode  = GPIO_MODE_OUTPUT_PP;
+  gpio_init_structure.Pull  = GPIO_NOPULL;
+  gpio_init_structure.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+
+  HAL_GPIO_Init(RF_SW_CTRL1_GPIO_PORT, &gpio_init_structure);
+
+  gpio_init_structure.Pin = RF_SW_CTRL2_PIN;
+  HAL_GPIO_Init(RF_SW_CTRL2_GPIO_PORT, &gpio_init_structure);
+
+  gpio_init_structure.Pin = RF_SW_CTRL3_PIN;
+  HAL_GPIO_Init(RF_SW_CTRL3_GPIO_PORT, &gpio_init_structure);
+
+  HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_RESET);
+  HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_RESET);
+  HAL_GPIO_WritePin(RF_SW_CTRL3_GPIO_PORT, RF_SW_CTRL3_PIN, GPIO_PIN_RESET);
+#endif
+
+  return 0;
 #else
-  /* 2/ Or implement RBI_Init here */
-  int32_t retcode = 0;
   /* USER CODE BEGIN RBI_Init_2 */
-#warning user to provide its board code or to call his board driver functions
+#error user to provide its board code or to call his board driver functions
   /* USER CODE END RBI_Init_2 */
-  return retcode;
+#endif /* USE_BSP_DRIVER  || YUNHORN_STS_WLE5CCxx  */
-#endif  /* USE_BSP_DRIVER  */
+  /* USER CODE BEGIN RBI_Init_3 */
+
+  /* USER CODE END RBI_Init_3 */
 }
 
 int32_t RBI_DeInit(void)
@@ -88,24 +124,44 @@ int32_t RBI_DeInit(void)
 
   /* USER CODE END RBI_DeInit_1 */
 #if defined(USE_BSP_DRIVER)
-  /* Important note: BSP code is board dependent
+  /* code generated by MX does not support BSP */
-   * STM32WL_Nucleo code can be found
+  /* In order to use BSP driver, add the correspondent files in the IDE workspace */
-   *       either in STM32CubeWL package under Drivers/BSP/STM32WLxx_Nucleo/
+  /* and define USE_BSP_DRIVER in the preprocessor definitions  or in platform.h */
-   *       or at https://github.com/STMicroelectronics/STM32CubeWL/tree/main/Drivers/BSP/STM32WLxx_Nucleo/
-   * 1/ For User boards, the BSP/STM32WLxx_Nucleo/ directory can be copied and replaced in the project. The copy must then be updated depending:
-   *       on board RF switch configuration (pin control, number of port etc)
-   *       on TCXO configuration
-   *       on DC/DC configuration
-   *       on maximum output power that the board can deliver*/
   return BSP_RADIO_DeInit();
+#elif defined(YUNHORN_STS_WLE5CCxx)
+
+#if defined(YUNHORN_STS_RF_CHANNEL_SWITCH)
+    RF_SW_CTRL1_GPIO_CLK_ENABLE();
+    RF_SW_CTRL2_GPIO_CLK_ENABLE();
+    /* Turn off switch */
+    HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_RESET);
+    HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_RESET);
+    /* DeInit the Radio Switch pin */
+    HAL_GPIO_DeInit(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN);
+    HAL_GPIO_DeInit(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN);
+#else
+  RF_SW_CTRL3_GPIO_CLK_ENABLE();
+
+  /* Turn off switch */
+  HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_RESET);
+  HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_RESET);
+  HAL_GPIO_WritePin(RF_SW_CTRL3_GPIO_PORT, RF_SW_CTRL3_PIN, GPIO_PIN_RESET);
+
+  /* DeInit the Radio Switch pin */
+  HAL_GPIO_DeInit(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN);
+  HAL_GPIO_DeInit(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN);
+  HAL_GPIO_DeInit(RF_SW_CTRL3_GPIO_PORT, RF_SW_CTRL3_PIN);
+#endif
+
+  return 0;
 #else
-  /* 2/ Or implement RBI_DeInit here */
-  int32_t retcode = 0;
   /* USER CODE BEGIN RBI_DeInit_2 */
-#warning user to provide its board code or to call his board driver functions
+#error user to provide its board code or to call his board driver functions
   /* USER CODE END RBI_DeInit_2 */
-  return retcode;
+#endif  /* USE_BSP_DRIVER  || MX_NUCLEO_WL55JC1 */
-#endif  /* USE_BSP_DRIVER */
+  /* USER CODE BEGIN RBI_DeInit_3 */
+
+  /* USER CODE END RBI_DeInit_3 */
 }
 
 int32_t RBI_ConfigRFSwitch(RBI_Switch_TypeDef Config)
@@ -114,25 +170,82 @@ int32_t RBI_ConfigRFSwitch(RBI_Switch_TypeDef Config)
 
   /* USER CODE END RBI_ConfigRFSwitch_1 */
 #if defined(USE_BSP_DRIVER)
-
+  /* code generated by MX does not support BSP */
-  /* Important note: BSP code is board dependent
+  /* In order to use BSP driver, add the correspondent files in the IDE workspace */
-   * STM32WL_Nucleo code can be found
+  /* and define USE_BSP_DRIVER in the preprocessor definitions  or in platform.h */
-   *       either in STM32CubeWL package under Drivers/BSP/STM32WLxx_Nucleo/
-   *       or at https://github.com/STMicroelectronics/STM32CubeWL/tree/main/Drivers/BSP/STM32WLxx_Nucleo/
-   * 1/ For User boards, the BSP/STM32WLxx_Nucleo/ directory can be copied and replaced in the project. The copy must then be updated depending:
-   *       on board RF switch configuration (pin control, number of port etc)
-   *       on TCXO configuration
-   *       on DC/DC configuration
-   *       on maximum output power that the board can deliver*/
   return BSP_RADIO_ConfigRFSwitch((BSP_RADIO_Switch_TypeDef) Config);
+#elif defined(YUNHORN_STS_WLE5CCxx)
+  switch (Config)
+  {
+    case RBI_SWITCH_OFF:
+    {
+#if defined(YUNHORN_STS_RF_CHANNEL_SWITCH)
+        /* Turn off switch */
+        HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_RESET);
+        HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_RESET);
+#else
+      /* Turn off switch */
+      HAL_GPIO_WritePin(RF_SW_CTRL3_GPIO_PORT, RF_SW_CTRL3_PIN, GPIO_PIN_RESET);
+      HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_RESET);
+      HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_RESET);
+#endif
+      break;
+    }
+    case RBI_SWITCH_RX:
+    {
+#if defined(YUNHORN_STS_RF_CHANNEL_SWITCH)
+        /*Turns On in Rx Mode the RF Switch */
+        HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_SET);
+        HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_RESET);
+#else
+      /*Turns On in Rx Mode the RF Switch */
+      HAL_GPIO_WritePin(RF_SW_CTRL3_GPIO_PORT, RF_SW_CTRL3_PIN, GPIO_PIN_SET);
+      HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_SET);
+      HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_RESET);
+#endif
+      break;
+    }
+    case RBI_SWITCH_RFO_LP:
+    {
+#if defined(YUNHORN_STS_RF_CHANNEL_SWITCH)
+        /*Turns On in Tx Low Power the RF Switch */
+        HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_RESET);
+        HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_SET);
+#else
+      /*Turns On in Tx Low Power the RF Switch */
+      HAL_GPIO_WritePin(RF_SW_CTRL3_GPIO_PORT, RF_SW_CTRL3_PIN, GPIO_PIN_SET);
+      HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_SET);
+      HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_SET);
+#endif
+      break;
+    }
+    case RBI_SWITCH_RFO_HP:
+    {
+#if defined(YUNHORN_STS_RF_CHANNEL_SWITCH)
+        /*Turns On in Tx High Power the RF Switch */
+        HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_RESET);
+        HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_SET);
+#else
+      /*Turns On in Tx High Power the RF Switch */
+      HAL_GPIO_WritePin(RF_SW_CTRL3_GPIO_PORT, RF_SW_CTRL3_PIN, GPIO_PIN_SET);
+      HAL_GPIO_WritePin(RF_SW_CTRL1_GPIO_PORT, RF_SW_CTRL1_PIN, GPIO_PIN_RESET);
+      HAL_GPIO_WritePin(RF_SW_CTRL2_GPIO_PORT, RF_SW_CTRL2_PIN, GPIO_PIN_SET);
+#endif
+      break;
+    }
+    default:
+      break;
+  }
+
+  return 0;
 #else
-  /* 2/ Or implement RBI_ConfigRFSwitch here */
-  int32_t retcode = 0;
   /* USER CODE BEGIN RBI_ConfigRFSwitch_2 */
-#warning user to provide its board code or to call his board driver functions
+#error user to provide its board code or to call his board driver functions
   /* USER CODE END RBI_ConfigRFSwitch_2 */
-  return retcode;
+#endif /* USE_BSP_DRIVER  || YUNHORN_STS_WLE5CCxx */
-#endif  /* USE_BSP_DRIVER */
+  /* USER CODE BEGIN RBI_ConfigRFSwitch_3 */
+
+  /* USER CODE END RBI_ConfigRFSwitch_3 */
 }
 
 int32_t RBI_GetTxConfig(void)
@@ -141,24 +254,44 @@ int32_t RBI_GetTxConfig(void)
 
   /* USER CODE END RBI_GetTxConfig_1 */
 #if defined(USE_BSP_DRIVER)
-  /* Important note: BSP code is board dependent
+  /* code generated by MX does not support BSP */
-   * STM32WL_Nucleo code can be found
+  /* In order to use BSP driver, add the correspondent files in the IDE workspace */
-   *       either in STM32CubeWL package under Drivers/BSP/STM32WLxx_Nucleo/
+  /* and define USE_BSP_DRIVER in the preprocessor definitions  or in platform.h */
-   *       or at https://github.com/STMicroelectronics/STM32CubeWL/tree/main/Drivers/BSP/STM32WLxx_Nucleo/
-   * 1/ For User boards, the BSP/STM32WLxx_Nucleo/ directory can be copied and replaced in the project. The copy must then be updated depending:
-   *       on board RF switch configuration (pin control, number of port etc)
-   *       on TCXO configuration
-   *       on DC/DC configuration
-   *       on maximum output power that the board can deliver*/
   return BSP_RADIO_GetTxConfig();
+
+#elif defined(YUNHORN_STS_WLE5CCxx)
+  return RBI_CONF_RFO;
 #else
-  /* 2/ Or implement RBI_GetTxConfig here */
-  int32_t retcode = RBI_CONF_RFO;
   /* USER CODE BEGIN RBI_GetTxConfig_2 */
-#warning user to provide its board code or to call his board driver functions
+#error user to provide its board code or to call his board driver functions
   /* USER CODE END RBI_GetTxConfig_2 */
-  return retcode;
+#endif /* USE_BSP_DRIVER  || YUNHORN_STS_WLE5CCxx */
-#endif  /* USE_BSP_DRIVER */
+  /* USER CODE BEGIN RBI_GetTxConfig_3 */
+
+  /* USER CODE END RBI_GetTxConfig_3 */
+}
+
+int32_t RBI_GetWakeUpTime(void)
+{
+  /* USER CODE BEGIN RBI_GetWakeUpTime_1 */
+
+  /* USER CODE END RBI_GetWakeUpTime_1 */
+#if defined(USE_BSP_DRIVER)
+  /* code generated by MX does not support BSP */
+  /* In order to use BSP driver, add the correspondent files in the IDE workspace */
+  /* and define USE_BSP_DRIVER in the preprocessor definitions  or in platform.h */
+  return  BSP_RADIO_GetWakeUpTime();
+
+#elif defined(YUNHORN_STS_WLE5CCxx)
+  return RF_WAKEUP_TIME;
+#else
+  /* USER CODE BEGIN RBI_GetWakeUpTime_2 */
+#error user to provide its board code or to call his board driver functions
+  /* USER CODE END RBI_GetWakeUpTime_2 */
+#endif /* USE_BSP_DRIVER  || YUNHORN_STS_WLE5CCxx */
+  /* USER CODE BEGIN RBI_GetWakeUpTime_3 */
+
+  /* USER CODE END RBI_GetWakeUpTime_3 */
 }
 
 int32_t RBI_IsTCXO(void)
@@ -167,24 +300,21 @@ int32_t RBI_IsTCXO(void)
 
   /* USER CODE END RBI_IsTCXO_1 */
 #if defined(USE_BSP_DRIVER)
-  /* Important note: BSP code is board dependent
+  /* code generated by MX does not support BSP */
-   * STM32WL_Nucleo code can be found
+  /* In order to use BSP driver, add the correspondent files in the IDE workspace */
-   *       either in STM32CubeWL package under Drivers/BSP/STM32WLxx_Nucleo/
+  /* and define USE_BSP_DRIVER in the preprocessor definitions  or in platform.h */
-   *       or at https://github.com/STMicroelectronics/STM32CubeWL/tree/main/Drivers/BSP/STM32WLxx_Nucleo/
-   * 1/ For User boards, the BSP/STM32WLxx_Nucleo/ directory can be copied and replaced in the project. The copy must then be updated depending:
-   *       on board RF switch configuration (pin control, number of port etc)
-   *       on TCXO configuration
-   *       on DC/DC configuration
-   *       on maximum output power that the board can deliver*/
   return BSP_RADIO_IsTCXO();
+
+#elif defined(YUNHORN_STS_WLE5CCxx)
+  return IS_TCXO_SUPPORTED;
 #else
-  /* 2/ Or implement RBI_IsTCXO here */
-  int32_t retcode = IS_TCXO_SUPPORTED;
   /* USER CODE BEGIN RBI_IsTCXO_2 */
-#warning user to provide its board code or to call his board driver functions
+#error user to provide its board code or to call his board driver functions
   /* USER CODE END RBI_IsTCXO_2 */
-  return retcode;
+#endif /* USE_BSP_DRIVER   || YUNHORN_STS_WLE5CCxx */
-#endif  /* USE_BSP_DRIVER  */
+  /* USER CODE BEGIN RBI_IsTCXO_3 */
+
+  /* USER CODE END RBI_IsTCXO_3 */
 }
 
 int32_t RBI_IsDCDC(void)
@@ -193,24 +323,21 @@ int32_t RBI_IsDCDC(void)
 
   /* USER CODE END RBI_IsDCDC_1 */
 #if defined(USE_BSP_DRIVER)
-  /* Important note: BSP code is board dependent
+  /* code generated by MX does not support BSP */
-   * STM32WL_Nucleo code can be found
+  /* In order to use BSP driver, add the correspondent files in the IDE workspace */
-   *       either in STM32CubeWL package under Drivers/BSP/STM32WLxx_Nucleo/
+  /* and define USE_BSP_DRIVER in the preprocessor definitions  or in platform.h */
-   *       or at https://github.com/STMicroelectronics/STM32CubeWL/tree/main/Drivers/BSP/STM32WLxx_Nucleo/
-   * 1/ For User boards, the BSP/STM32WLxx_Nucleo/ directory can be copied and replaced in the project. The copy must then be updated depending:
-   *       on board RF switch configuration (pin control, number of port etc)
-   *       on TCXO configuration
-   *       on DC/DC configuration
-   *       on maximum output power that the board can deliver*/
   return BSP_RADIO_IsDCDC();
+
+#elif defined(YUNHORN_STS_WLE5CCxx)
+  return IS_DCDC_SUPPORTED;
 #else
-  /* 2/ Or implement RBI_IsDCDC here */
-  int32_t retcode = IS_DCDC_SUPPORTED;
   /* USER CODE BEGIN RBI_IsDCDC_2 */
-#warning user to provide its board code or to call his board driver functions
+#error user to provide its board code or to call his board driver functions
   /* USER CODE END RBI_IsDCDC_2 */
-  return retcode;
+#endif /* USE_BSP_DRIVER   || YUNHORN_STS_WLE5CCxx */
-#endif  /* USE_BSP_DRIVER  */
+  /* USER CODE BEGIN RBI_IsDCDC_3 */
+
+  /* USER CODE END RBI_IsDCDC_3 */
 }
 
 int32_t RBI_GetRFOMaxPowerConfig(RBI_RFOMaxPowerConfig_TypeDef Config)
@@ -233,7 +360,7 @@ int32_t RBI_GetRFOMaxPowerConfig(RBI_RFOMaxPowerConfig_TypeDef Config)
   /* 2/ Or implement RBI_RBI_GetRFOMaxPowerConfig here */
   int32_t ret = 0;
   /* USER CODE BEGIN RBI_GetRFOMaxPowerConfig_2 */
-#warning user to provide its board code or to call his board driver functions
+  /* #warning user to provide its board code or to call his board driver functions */
   if (Config == RBI_RFO_LP_MAXPOWER)
   {
     ret = 15; /*dBm*/
@@ -246,6 +373,7 @@ int32_t RBI_GetRFOMaxPowerConfig(RBI_RFOMaxPowerConfig_TypeDef Config)
   return ret;
 #endif  /* USE_BSP_DRIVER  */
 }
+
 /* USER CODE BEGIN EF */
 
 /* USER CODE END EF */
@@ -254,3 +382,5 @@ int32_t RBI_GetRFOMaxPowerConfig(RBI_RFOMaxPowerConfig_TypeDef Config)
 /* USER CODE BEGIN PrFD */
 
 /* USER CODE END PrFD */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LoRaWAN/Target/radio_board_if.h

@@ -1,22 +1,21 @@
-/* USER CODE BEGIN Header */
 /**
  ******************************************************************************
  * @file    radio_board_if.h
-  * @author  MCD Application Team
+ * @author  YunHorn Technology Limited Application Team
  * @brief   Header for Radio interface configuration
  ******************************************************************************
  * @attention
  *
-  * Copyright (c) 2021 STMicroelectronics.
+ * Copyright (c) 2023 YunHorn Technology Limited.
-  * All rights reserved.
+ * All rights reserved.</center></h2>
  *
-  * This software is licensed under terms that can be found in the LICENSE file
+ * This software component is licensed by ST under Ultimate Liberty license
-  * in the root directory of this software component.
+ * SLA0044, the "License"; You may not use this file except in compliance with
-  * If no LICENSE file comes with this software, it is provided AS-IS.
+ * the License. You may obtain a copy of the License at:
+ *                             www.st.com/SLA0044
  *
  ******************************************************************************
  */
-/* USER CODE END Header */
 
 /* Define to prevent recursive inclusion -------------------------------------*/
 #ifndef RADIO_BOARD_IF_H
@@ -33,43 +32,50 @@ extern "C" {
 /* USER CODE END include */
 
 /* Exported defines ----------------------------------------------------------*/
+// #ifdef MX_BOARD_PSEUDODRIVER
+#define YUNHORN_STS_WLE5CCxx
+// #endif /* MX_BOARD_PSEUDODRIVER */
 #if defined(USE_BSP_DRIVER)
-/* code generated by STM32CubeMX does not support BSP */
+/* code generated by MX does not support BSP */
 /* In order to use BSP driver, add the correspondent files in the IDE workspace */
 /* and define USE_BSP_DRIVER in the preprocessor definitions  or in platform.h */
 #define RBI_CONF_RFO_LP_HP  RADIO_CONF_RFO_LP_HP
 #define RBI_CONF_RFO_LP     RADIO_CONF_RFO_LP
 #define RBI_CONF_RFO_HP     RADIO_CONF_RFO_HP
-#else
+#elif defined(YUNHORN_STS_WLE5CCxx)
-/* USER CODE BEGIN Board Definition */
-
-/* USER CODE END Board Definition */
 #define RBI_CONF_RFO_LP_HP  0
 #define RBI_CONF_RFO_LP     1
 #define RBI_CONF_RFO_HP     2
-/* USER CODE BEGIN Board Definition_2 */
+#define YUNHORN_STS_RF_CHANNEL_SWITCH  1
-
+#else
-/* USER CODE END Board Definition_2 */
+/* USER CODE BEGIN Board Definition */
-#endif  /* USE_BSP_DRIVER  */
+#error user to provide its board definitions
+/* USER CODE END Board Definition */
+#endif /* USE_BSP_DRIVER  || YUNHORN_STS_WLE5CCxx  */
 
 #if defined(USE_BSP_DRIVER)
-/* code generated by STM32CubeMX does not support BSP */
+/* code generated by MX does not support BSP */
 /* In order to use BSP driver, add the correspondent files in the IDE workspace */
 /* and define USE_BSP_DRIVER in the preprocessor definitions  or in platform.h */
 
-#else
+#elif defined(YUNHORN_STS_WLE5CCxx)
-/* USER CODE BEGIN Exported Parameters */
 
-/* USER CODE END Exported Parameters */
 /* Indicates the type of switch between the ones proposed by CONFIG Constants
  */
-#define RBI_CONF_RFO                        RBI_CONF_RFO_LP_HP
+#if defined(YUNHORN_STS_RF_CHANNEL_SWITCH)
+  #define RBI_CONF_RFO RBI_CONF_RFO_HP
+#else
+  #define RBI_CONF_RFO                        RBI_CONF_RFO_LP_HP
+#endif
+
+/* Radio maximum wakeup time (in ms) */
+#define RF_WAKEUP_TIME                     10U
 
 /* Indicates whether or not TCXO is supported by the board
  * 0: TCXO not supported
  * 1: TCXO supported
  */
-#define IS_TCXO_SUPPORTED                   1U
+#define IS_TCXO_SUPPORTED                   0U
 
 /* Indicates whether or not DCDC is supported by the board
  * 0: DCDC not supported
@@ -77,30 +83,65 @@ extern "C" {
  */
 #define IS_DCDC_SUPPORTED                   1U
 
-/* USER CODE BEGIN Exported Parameters_2 */
+#else
-
+/* USER CODE BEGIN Exported Parameters */
-/* USER CODE END Exported Parameters_2 */
+#error user to provide its board definitions
-#endif  /* USE_BSP_DRIVER  */
+/* USER CODE END Exported Parameters */
+#endif  /* USE_BSP_DRIVER  || MX_NUCLEO_WL55JC1  */
 
 #if defined(USE_BSP_DRIVER)
-/* code generated by STM32CubeMX does not support BSP */
+/* code generated by MX does not support BSP */
 /* In order to use BSP driver, add the correspondent files in the IDE workspace */
 /* and define USE_BSP_DRIVER in the preprocessor definitions  or in platform.h */
 
+#elif defined(YUNHORN_STS_WLE5CCxx)
+
+#if defined(YUNHORN_STS_RF_CHANNEL_SWITCH)
+  #define RF_SW_CTRL1_PIN GPIO_PIN_8
+  #define RF_SW_CTRL1_GPIO_PORT GPIOB
+  #define RF_SW_CTRL1_GPIO_CLK_ENABLE() __HAL_RCC_GPIOB_CLK_ENABLE()
+  #define RF_SW_CTRL1_GPIO_CLK_DISABLE() __HAL_RCC_GPIOB_CLK_DISABLE()
+
+  #define RF_SW_CTRL2_PIN GPIO_PIN_13
+  #define RF_SW_CTRL2_GPIO_PORT GPIOC
+  #define RF_SW_CTRL2_GPIO_CLK_ENABLE() __HAL_RCC_GPIOC_CLK_ENABLE()
+  #define RF_SW_CTRL2_GPIO_CLK_DISABLE() __HAL_RCC_GPIOC_CLK_DISABLE()
+#else
+#define RF_SW_CTRL3_PIN                          GPIO_PIN_3
+#define RF_SW_CTRL3_GPIO_PORT                    GPIOC
+#define RF_SW_CTRL3_GPIO_CLK_ENABLE()            __HAL_RCC_GPIOC_CLK_ENABLE()
+#define RF_SW_CTRL3_GPIO_CLK_DISABLE()           __HAL_RCC_GPIOC_CLK_DISABLE()
+
+#define RF_SW_CTRL1_PIN                          GPIO_PIN_4
+#define RF_SW_CTRL1_GPIO_PORT                    GPIOC
+#define RF_SW_CTRL1_GPIO_CLK_ENABLE()            __HAL_RCC_GPIOC_CLK_ENABLE()
+#define RF_SW_RX_GPIO_CLK_DISABLE()              __HAL_RCC_GPIOC_CLK_DISABLE()
+
+#define RF_SW_CTRL2_PIN                          GPIO_PIN_5
+#define RF_SW_CTRL2_GPIO_PORT                    GPIOC
+#define RF_SW_CTRL2_GPIO_CLK_ENABLE()            __HAL_RCC_GPIOC_CLK_ENABLE()
+#define RF_SW_CTRL2_GPIO_CLK_DISABLE()           __HAL_RCC_GPIOC_CLK_DISABLE()
+#endif
+
+/* To be checked vs TCXO management in RCC config */
+#define RF_TCXO_VCC_PIN                          GPIO_PIN_0
+#define RF_TCXO_VCC_GPIO_PORT                    GPIOB
+#define RF_TCXO_VCC_CLK_ENABLE()                 __HAL_RCC_GPIOB_CLK_ENABLE()
+#define RF_TCXO_VCC_CLK_DISABLE()                __HAL_RCC_GPIOB_CLK_DISABLE()
 #else
 /* USER CODE BEGIN Exported PinMapping */
-#warning user to provide its board definitions pins
+#error user to provide its board definitions
 /* USER CODE END Exported PinMapping */
-#endif  /* USE_BSP_DRIVER  */
+#endif /* USE_BSP_DRIVER || YUNHORN_STS_WLE5CCxx  */
 
-/* USER CODE BEGIN ED */
+/* USER CODE BEGIN Exported_Defines */
 
-/* USER CODE END ED */
+/* USER CODE END Exported_Defines */
 
 /* Exported types ------------------------------------------------------------*/
 
 #if defined(USE_BSP_DRIVER)
-/* code generated by STM32CubeMX does not support BSP */
+/* code generated by MX does not support BSP */
 /* In order to use BSP driver, add the correspondent files in the IDE workspace */
 /* and define USE_BSP_DRIVER in the preprocessor definitions  or in platform.h */
 typedef enum
@@ -110,17 +151,7 @@ typedef enum
   RBI_SWITCH_RFO_LP = RADIO_SWITCH_RFO_LP,
   RBI_SWITCH_RFO_HP = RADIO_SWITCH_RFO_HP,
 } RBI_Switch_TypeDef;
-
+#elif defined(YUNHORN_STS_WLE5CCxx)
-typedef enum
-{
-  RBI_RFO_LP_MAXPOWER = RADIO_RFO_LP_MAXPOWER,
-  RBI_RFO_HP_MAXPOWER = RADIO_RFO_HP_MAXPOWER,
-} RBI_RFOMaxPowerConfig_TypeDef;
-
-#else
-/* USER CODE BEGIN Exported Types */
-
-/* USER CODE END Exported Types */
 typedef enum
 {
   RBI_SWITCH_OFF    = 0,
@@ -134,10 +165,12 @@ typedef enum
   RBI_RFO_LP_MAXPOWER = 0,
   RBI_RFO_HP_MAXPOWER = 1,
 } RBI_RFOMaxPowerConfig_TypeDef;
-/* USER CODE BEGIN Exported Types_2 */
 
-/* USER CODE END Exported Types_2 */
+#else
-#endif  /* USE_BSP_DRIVER */
+/* USER CODE BEGIN Exported Types */
+#error user to provide its board definitions
+/* USER CODE END Exported Types */
+#endif /* USE_BSP_DRIVER  || YUNHORN_STS_WLE5CCxx */
 
 /* USER CODE BEGIN ET */
 
@@ -191,6 +224,12 @@ int32_t RBI_ConfigRFSwitch(RBI_Switch_TypeDef Config);
   */
 int32_t RBI_GetTxConfig(void);
 
+/**
+  * @brief  Get Radio Wake Time
+  * @return the wake upt time in ms
+  */
+int32_t RBI_GetWakeUpTime(void);
+
 /**
   * @brief  Get If TCXO is to be present on board
   * @note   never remove called by MW,
@@ -206,9 +245,9 @@ int32_t RBI_IsTCXO(void);
 int32_t RBI_IsDCDC(void);
 
 /**
-  * @brief  Return RF Output Max Power Configuration of matching circuit
+  * @brief  Get RFO Max Power Config on board
   * @note   never remove called by MW,
-  * @retval return Max Power configuration of matching circuit for Low Power or High Power mode in dBm
+  * @retval return 15 dBm for low power, 22 dBm for high power
   */
 int32_t RBI_GetRFOMaxPowerConfig(RBI_RFOMaxPowerConfig_TypeDef Config);
 
@@ -221,3 +260,5 @@ int32_t RBI_GetRFOMaxPowerConfig(RBI_RFOMaxPowerConfig_TypeDef Config);
 #endif
 
 #endif /* RADIO_BOARD_IF_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

LoRaWAN/Target/radio_conf.h

@@ -1,22 +1,21 @@
-/* USER CODE BEGIN Header */
 /**
  ******************************************************************************
  * @file    radio_conf.h
-  * @author  MCD Application Team
+ * @author  YunHorn Technology Limited Application Team
  * @brief   Header of Radio configuration
  ******************************************************************************
  * @attention
  *
-  * Copyright (c) 2021 STMicroelectronics.
+ * Copyright (c) 2023 YunHorn Technology Limited.
-  * All rights reserved.
+ * All rights reserved.</center></h2>
  *
-  * This software is licensed under terms that can be found in the LICENSE file
+ * This software component is licensed by ST under Ultimate Liberty license
-  * in the root directory of this software component.
+ * SLA0044, the "License"; You may not use this file except in compliance with
-  * If no LICENSE file comes with this software, it is provided AS-IS.
+ * the License. You may obtain a copy of the License at:
+ *                             www.st.com/SLA0044
  *
  ******************************************************************************
  */
-/* USER CODE END Header */
 
 /* Define to prevent recursive inclusion -------------------------------------*/
 #ifndef __RADIO_CONF_H__
@@ -29,7 +28,7 @@ extern "C" {
 /* Includes ------------------------------------------------------------------*/
 #include "platform.h"
 #include "subghz.h"
-#include "stm32_mem.h"       /* RADIO_MEMSET8 def in this file */
+#include "stm32_mem.h"
 #include "mw_log_conf.h"     /* mw trace conf */
 #include "radio_board_if.h"  /* low layer api (bsp) */
 #include "utilities_def.h"  /* low layer api (bsp) */
@@ -44,66 +43,6 @@ extern "C" {
 /* USER CODE END ET */
 
 /* Exported constants --------------------------------------------------------*/
-
-/**
-  * @brief drive value used anytime radio is NOT in TX low power mode
-  * @note override the default configuration of radio_driver.c
-  */
-#define SMPS_DRIVE_SETTING_DEFAULT  SMPS_DRV_40
-
-/**
-  * @brief drive value used anytime radio is in TX low power mode
-  *        TX low power mode is the worst case because the PA sinks from SMPS
-  *        while in high power mode, current is sunk directly from the battery
-  * @note override the default configuration of radio_driver.c
-  */
-#define SMPS_DRIVE_SETTING_MAX      SMPS_DRV_60
-
-/**
-  * @brief Provides the frequency of the chip running on the radio and the frequency step
-  * @remark These defines are used for computing the frequency divider to set the RF frequency
-  * @note override the default configuration of radio_driver.c
-  */
-#define XTAL_FREQ                   ( 32000000UL )
-
-/**
-  * @brief in XO mode, set internal capacitor (from 0x00 to 0x2F starting 11.2pF with 0.47pF steps)
-  * @note override the default configuration of radio_driver.c
-  */
-#define XTAL_DEFAULT_CAP_VALUE      ( 0x20UL )
-
-/**
-  * @brief voltage of vdd tcxo.
-  * @note override the default configuration of radio_driver.c
-  */
-#define TCXO_CTRL_VOLTAGE           TCXO_CTRL_1_7V
-
-/**
-  * @brief Radio maximum wakeup time (in ms)
-  * @note override the default configuration of radio_driver.c
-  */
-#define RF_WAKEUP_TIME              ( 1UL )
-
-/**
-  * @brief DCDC is enabled
-  * @remark this define is only used if the DCDC is present on the board
-  * @note override the default configuration of radio_driver.c
-  */
-#define DCDC_ENABLE                 ( 1UL )
-
-/* USER CODE BEGIN EC */
-/**
-  * @brief disable the Sigfox radio modulation
-  * @note enabled by default
-  */
-#define RADIO_SIGFOX_ENABLE 0
-
-/**
-  * @brief disable the radio generic features
-  * @note enabled by default
-  */
-#define RADIO_GENERIC_CONFIG_ENABLE 0
-
 /**
   * @brief Set RX pin to high or low level
   */
@@ -114,6 +53,41 @@ extern "C" {
   */
 #define DBG_GPIO_RADIO_TX(set_rst) PROBE_GPIO_##set_rst##_LINE(PROBE_LINE2_PORT, PROBE_LINE2_PIN);
 
+/**
+  * @brief Max payload buffer size
+  */
+#define RADIO_RX_BUF_SIZE          255
+
+/**
+  * @brief drive value used anytime radio is NOT in TX low power mode
+  */
+#define SMPS_DRIVE_SETTING_DEFAULT  SMPS_DRV_40
+
+/**
+  * @brief drive value used anytime radio is in TX low power mode
+  *        TX low power mode is the worst case because the PA sinks from SMPS
+  *        while in high power mode, current is sunk directly from the battery
+  */
+#define SMPS_DRIVE_SETTING_MAX      SMPS_DRV_60
+
+/**
+  * @brief in XO mode, set internal capacitor (from 0x00 to 0x2F starting 11.2pF with 0.47pF steps)
+  */
+#define XTAL_DEFAULT_CAP_VALUE      0x10
+
+/**
+  * @brief Frequency error (in Hz) can be compensated here.
+  *        warning XO frequency error generates (de)modulator sampling time error which can not be compensated
+  */
+#define RF_FREQUENCY_ERROR          ((int32_t) 0)
+
+/**
+  * @brief voltage of vdd tcxo.
+  */
+#define TCXO_CTRL_VOLTAGE           TCXO_CTRL_1_7V
+
+/* USER CODE BEGIN EC */
+
 /* USER CODE END EC */
 
 /* External variables --------------------------------------------------------*/
@@ -170,3 +144,5 @@ extern "C" {
 #endif
 
 #endif /* __RADIO_CONF_H__*/
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

STM32CubeIDE/Application/User/TOF/App/app_tof.c

@@ -65,7 +65,7 @@ void MX_TOF_Init(void)
   APP_LOG(TS_OFF,VLEVEL_L,"\r\n######################    MX TOF Init... \r\n");
 
   //MX_53L1A2_SimpleRanging_Init();
-
+  STS_TOF_VL53LX_PeopleCounting_Process();
   /* USER CODE BEGIN TOF_Init_PostTreatment */
 
   /* USER CODE END TOF_Init_PostTreatment */
@@ -81,11 +81,11 @@ void MX_TOF_Process(void)
   /* USER CODE END TOF_Process_PreTreatment */
 
 
-	APP_LOG(TS_OFF,VLEVEL_L,"\r\n######################    MX TOF Process... \r\n");
+	//APP_LOG(TS_OFF,VLEVEL_L,"\r\n######################    MX TOF Process... \r\n");
 	//STS_TOF_VL53LX_Range_Process();
-	STS_TOF_VL53LX_PeopleCounting_Process();
+	//STS_TOF_VL53LX_PeopleCounting_Process();
-
 
+	sts_tof_vl53lx_peoplecount_subprocess();
 
   /* USER CODE BEGIN TOF_Process_PostTreatment */
 

STM32CubeIDE/Application/User/TOF/App/app_tof.h

@@ -35,7 +35,7 @@ void MX_TOF_Init(void);
 void MX_TOF_Process(void);
 void STS_TOF_VL53LX_Range_Process(void);
 void STS_TOF_VL53LX_PeopleCounting_Process(void);
-
+int sts_tof_vl53lx_peoplecount_subprocess(void);
 
 
 #ifdef __cplusplus

STM32CubeIDE/Release/Application/User/Core/adc_if.d

@@ -46,10 +46,7 @@ Application/User/Core/adc_if.o: \
  ../../Core/Inc/stm32wlxx_nucleo.h ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h ../../Core/Inc/platform.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
+ ../../Core/Inc/sys_app.h ../../Core/Inc/sys_conf.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
- ../../Core/Inc/stm32wlxx_nucleo_conf.h ../../Core/Inc/sys_app.h \
- ../../Core/Inc/sys_conf.h \
  ../../../../../../../Utilities/trace/adv_trace/stm32_adv_trace.h \
  ../../Core/Inc/utilities_conf.h \
  ../../../../../../../Drivers/CMSIS/Include/cmsis_compiler.h \
@@ -106,9 +103,6 @@ Application/User/Core/adc_if.o: \
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../Core/Inc/platform.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/sys_app.h:
 ../../Core/Inc/sys_conf.h:
 ../../../../../../../Utilities/trace/adv_trace/stm32_adv_trace.h:

STM32CubeIDE/Release/Application/User/Core/flash_if.d

@@ -47,9 +47,6 @@ Application/User/Core/flash_if.o: \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
- ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../../../../../../Utilities/misc/stm32_mem.h \
  ../../Core/Inc/utilities_conf.h \
  ../../../../../../../Drivers/CMSIS/Include/cmsis_compiler.h \
@@ -104,9 +101,6 @@ Application/User/Core/flash_if.o: \
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../../../../../../Utilities/misc/stm32_mem.h:
 ../../Core/Inc/utilities_conf.h:
 ../../../../../../../Drivers/CMSIS/Include/cmsis_compiler.h:

STM32CubeIDE/Release/Application/User/Core/stm32_lpm_if.d

@@ -47,9 +47,6 @@ Application/User/Core/stm32_lpm_if.o: \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
- ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../../../../../../Utilities/lpm/tiny_lpm/stm32_lpm.h \
  ../../Core/Inc/stm32_lpm_if.h ../../Core/Inc/usart_if.h \
  ../../../../../../../Utilities/trace/adv_trace/stm32_adv_trace.h \
@@ -107,9 +104,6 @@ Application/User/Core/stm32_lpm_if.o: \
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../../../../../../Utilities/lpm/tiny_lpm/stm32_lpm.h:
 ../../Core/Inc/stm32_lpm_if.h:
 ../../Core/Inc/usart_if.h:

STM32CubeIDE/Release/Application/User/Core/sys_app.d

@@ -47,10 +47,7 @@ Application/User/Core/sys_app.o: \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
+ ../../Core/Inc/sys_app.h ../../Core/Inc/sys_conf.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
- ../../Core/Inc/stm32wlxx_nucleo_conf.h ../../Core/Inc/sys_app.h \
- ../../Core/Inc/sys_conf.h \
  ../../../../../../../Utilities/trace/adv_trace/stm32_adv_trace.h \
  ../../Core/Inc/utilities_conf.h \
  ../../../../../../../Drivers/CMSIS/Include/cmsis_compiler.h \
@@ -113,9 +110,6 @@ Application/User/Core/sys_app.o: \
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/sys_app.h:
 ../../Core/Inc/sys_conf.h:
 ../../../../../../../Utilities/trace/adv_trace/stm32_adv_trace.h:

STM32CubeIDE/Release/Application/User/Core/sys_debug.d

@@ -47,10 +47,8 @@ Application/User/Core/sys_debug.o: \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
+ ../../Core/Inc/sys_debug.h ../../Core/Inc/sys_conf.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
+ ../../Core/Inc/platform.h
- ../../Core/Inc/stm32wlxx_nucleo_conf.h ../../Core/Inc/sys_debug.h \
- ../../Core/Inc/sys_conf.h ../../Core/Inc/platform.h
 ../../Core/Inc/platform.h:
 ../../../../../../../Drivers/CMSIS/Device/ST/STM32WLxx/Include/stm32wlxx.h:
 ../../../../../../../Drivers/CMSIS/Device/ST/STM32WLxx/Include/stm32wl55xx.h:
@@ -99,9 +97,6 @@ Application/User/Core/sys_debug.o: \
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/sys_debug.h:
 ../../Core/Inc/sys_conf.h:
 ../../Core/Inc/platform.h:

STM32CubeIDE/Release/Application/User/Core/sys_sensors.d

@@ -47,11 +47,8 @@ Application/User/Core/sys_sensors.o: \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
+ ../../Core/Inc/sys_conf.h ../../Core/Inc/sys_sensors.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
+ ../../Core/Inc/adc_if.h ../../Core/Inc/adc.h ../../Core/Inc/platform.h
- ../../Core/Inc/stm32wlxx_nucleo_conf.h ../../Core/Inc/sys_conf.h \
- ../../Core/Inc/sys_sensors.h ../../Core/Inc/adc_if.h \
- ../../Core/Inc/adc.h ../../Core/Inc/platform.h
 ../../Core/Inc/platform.h:
 ../../../../../../../Drivers/CMSIS/Device/ST/STM32WLxx/Include/stm32wlxx.h:
 ../../../../../../../Drivers/CMSIS/Device/ST/STM32WLxx/Include/stm32wl55xx.h:
@@ -100,9 +97,6 @@ Application/User/Core/sys_sensors.o: \
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/sys_conf.h:
 ../../Core/Inc/sys_sensors.h:
 ../../Core/Inc/adc_if.h:

STM32CubeIDE/Release/Application/User/LoRaWAN/App/lora_app.d

@@ -47,10 +47,7 @@ Application/User/LoRaWAN/App/lora_app.o: \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
+ ../../Core/Inc/sys_app.h ../../Core/Inc/sys_conf.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
- ../../Core/Inc/stm32wlxx_nucleo_conf.h ../../Core/Inc/sys_app.h \
- ../../Core/Inc/sys_conf.h \
  ../../../../../../../Utilities/trace/adv_trace/stm32_adv_trace.h \
  ../../Core/Inc/utilities_conf.h \
  ../../../../../../../Drivers/CMSIS/Include/cmsis_compiler.h \
@@ -134,9 +131,6 @@ Application/User/LoRaWAN/App/lora_app.o: \
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/sys_app.h:
 ../../Core/Inc/sys_conf.h:
 ../../../../../../../Utilities/trace/adv_trace/stm32_adv_trace.h:

STM32CubeIDE/Release/Application/User/LoRaWAN/Target/radio_board_if.d

@@ -47,10 +47,7 @@ Application/User/LoRaWAN/Target/radio_board_if.o: \
  ../../Core/Inc/main.h ../../Core/Inc/stm32wlxx_nucleo.h \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
- ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
+ ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
- ../../Core/Inc/stm32wlxx_nucleo_conf.h
 D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/LoRaWAN/Target/radio_board_if.h:
 ../../Core/Inc/platform.h:
 ../../../../../../../Drivers/CMSIS/Device/ST/STM32WLxx/Include/stm32wlxx.h:
@@ -100,6 +97,3 @@ D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/LoR
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:

STM32CubeIDE/Release/Application/User/TOF/App/app_tof.su

@@ -1,5 +1,5 @@
-../Application/User/TOF/App/app_tof.c:54:6:MX_TOF_Init	0	static
+../Application/User/TOF/App/app_tof.c:54:6:MX_TOF_Init	8	static
-../Application/User/TOF/App/app_tof.c:77:6:MX_TOF_Process	8	static
+../Application/User/TOF/App/app_tof.c:77:6:MX_TOF_Process	0	static
 ../Application/User/TOF/App/app_tof.c:111:9:IsInterruptDetected	8	static
 ../Application/User/TOF/App/app_tof.c:192:6:BSP_PB_Callback	0	static
 ../Application/User/TOF/App/app_tof.c:198:5:sts_vl53lx_ranging	48	static

STM32CubeIDE/Release/Application/User/TOF/App/app_tof_peoplecount.cyclo

@@ -1,3 +1,4 @@
-D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:42:5:ProcessPeopleCountingData	22
+D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:43:5:ProcessPeopleCountingData	22
-D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:209:5:sts_tof_vl53lx_peoplecount	9
+D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:210:5:sts_tof_vl53lx_peoplecount	9
-D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:202:6:STS_TOF_VL53LX_PeopleCounting_Process	1
+D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:203:6:STS_TOF_VL53LX_PeopleCounting_Process	1
+D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:313:5:sts_tof_vl53lx_peoplecount_subprocess	7

STM32CubeIDE/Release/Application/User/TOF/App/app_tof_peoplecount.su

@@ -1,3 +1,4 @@
-D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:42:5:ProcessPeopleCountingData	32	static
+D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:43:5:ProcessPeopleCountingData	32	static
-D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:209:5:sts_tof_vl53lx_peoplecount	72	static
+D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:210:5:sts_tof_vl53lx_peoplecount	72	static
-D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:202:6:STS_TOF_VL53LX_PeopleCounting_Process	8	static
+D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:203:6:STS_TOF_VL53LX_PeopleCounting_Process	8	static
+D://ONEDRIVE/STM32WLV13/STS_LoRaWAN/LoRaWAN_End_Node_AS923_POC_TOF_VL53L1A_P/TOF/App/app_tof_peoplecount.c:313:5:sts_tof_vl53lx_peoplecount_subprocess	48	static

STM32CubeIDE/Release/Middlewares/LoRaWAN/LmhpCompliance.d

@@ -47,9 +47,6 @@ Middlewares/LoRaWAN/LmhpCompliance.o: \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
- ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../../../../../../Middlewares/Third_Party/LoRaWAN/LmHandler/NvmDataMgmt.h \
  ../../../../../../../Middlewares/Third_Party/LoRaWAN/Mac/LoRaMac.h \
  ../../../../../../../Middlewares/Third_Party/LoRaWAN/Mac/LoRaMacInterfaces.h \
@@ -128,9 +125,6 @@ Middlewares/LoRaWAN/LmhpCompliance.o: \
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../../../../../../Middlewares/Third_Party/LoRaWAN/LmHandler/NvmDataMgmt.h:
 ../../../../../../../Middlewares/Third_Party/LoRaWAN/Mac/LoRaMac.h:
 ../../../../../../../Middlewares/Third_Party/LoRaWAN/Mac/LoRaMacInterfaces.h:

STM32CubeIDE/Release/Middlewares/LoRaWAN/LmhpPackagesRegistration.d

@@ -47,9 +47,6 @@ Middlewares/LoRaWAN/LmhpPackagesRegistration.o: \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
- ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/LoRaWAN/LmHandler/Packages/LmhpPackagesRegistration.h \
  D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/LoRaWAN/LmHandler/Packages/LmhPackage.h \
  ../../../../../../../Middlewares/Third_Party/LoRaWAN/LmHandler/LmHandlerTypes.h \
@@ -124,9 +121,6 @@ Middlewares/LoRaWAN/LmhpPackagesRegistration.o: \
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/LoRaWAN/LmHandler/Packages/LmhpPackagesRegistration.h:
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/LoRaWAN/LmHandler/Packages/LmhPackage.h:
 ../../../../../../../Middlewares/Third_Party/LoRaWAN/LmHandler/LmHandlerTypes.h:

STM32CubeIDE/Release/Middlewares/SubGHz_Phy/radio.cyclo

@@ -1,16 +1,14 @@
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1159:13:RadioCheckRfFrequency	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1659:13:RadioOnTxTimeoutIrq	3
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1664:13:RadioOnRxTimeoutIrq	3
-D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1932:16:RadioSetRxGenericConfig	1
-D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:2110:16:RadioSetTxGenericConfig	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:2348:23:RadioLrFhssSetCfg	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:2379:23:RadioLrFhssGetTimeOnAirInMs	1
+D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1603:16:RadioRead	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1598:13:RadioWrite	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1884:13:RadioTxCw	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1542:13:RadioSetRxDutyCycle	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1501:13:RadioRxBoosted	4
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1454:13:RadioStandby	1
-D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1603:16:RadioRead	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:737:21:RadioGetStatus	2
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1654:17:RadioGetWakeupTime	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1613:13:RadioReadRegisters	1
@@ -21,15 +19,17 @@ D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/ra
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1554:13:RadioStartCad	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1459:13:RadioRx	4
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1444:13:RadioSleep	1
-D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1311:23:RadioSend	8
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:845:17:RadioRandom	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:704:13:RadioInit	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1618:13:RadioSetMaxPayloadLength	3
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1635:13:RadioSetPublicNetwork	2
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:752:13:RadioSetModem	5
-D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1049:13:RadioSetTxConfig	6
+D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:2110:16:RadioSetTxGenericConfig	26
-D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:860:13:RadioSetRxConfig	7
+D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1932:16:RadioSetRxGenericConfig	19
+D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1049:13:RadioSetTxConfig	7
+D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:860:13:RadioSetRxConfig	8
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:808:13:RadioIsChannelFree	3
+D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1311:23:RadioSend	12
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1278:17:RadioTimeOnAir	9
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1876:13:RadioTxPrbs	1
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1696:13:RadioIrqProcess	40

STM32CubeIDE/Release/Middlewares/SubGHz_Phy/radio.d

@@ -53,10 +53,7 @@ Middlewares/SubGHz_Phy/radio.o: \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
+ ../../Core/Inc/subghz.h ../../../../../../../Utilities/misc/stm32_mem.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
- ../../Core/Inc/stm32wlxx_nucleo_conf.h ../../Core/Inc/subghz.h \
- ../../../../../../../Utilities/misc/stm32_mem.h \
  ../../Core/Inc/utilities_conf.h \
  ../../../../../../../Drivers/CMSIS/Include/cmsis_compiler.h \
  ../../../../../../../Utilities/misc/stm32_tiny_vsnprintf.h \
@@ -128,9 +125,6 @@ D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/ra
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/subghz.h:
 ../../../../../../../Utilities/misc/stm32_mem.h:
 ../../Core/Inc/utilities_conf.h:

STM32CubeIDE/Release/Middlewares/SubGHz_Phy/radio.su

@@ -1,16 +1,14 @@
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1159:13:RadioCheckRfFrequency	0	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1659:13:RadioOnTxTimeoutIrq	0	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1664:13:RadioOnRxTimeoutIrq	0	static
-D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1932:16:RadioSetRxGenericConfig	0	static
-D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:2110:16:RadioSetTxGenericConfig	0	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:2348:23:RadioLrFhssSetCfg	0	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:2379:23:RadioLrFhssGetTimeOnAirInMs	0	static
+D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1603:16:RadioRead	0	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1598:13:RadioWrite	0	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1884:13:RadioTxCw	8	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1542:13:RadioSetRxDutyCycle	16	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1501:13:RadioRxBoosted	8	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1454:13:RadioStandby	0	static
-D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1603:16:RadioRead	0	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:737:21:RadioGetStatus	8	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1654:17:RadioGetWakeupTime	8	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1613:13:RadioReadRegisters	0	static
@@ -21,15 +19,17 @@ D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/ra
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1554:13:RadioStartCad	8	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1459:13:RadioRx	8	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1444:13:RadioSleep	8	static
-D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1311:23:RadioSend	32	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:845:17:RadioRandom	8	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:704:13:RadioInit	24	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1618:13:RadioSetMaxPayloadLength	0	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1635:13:RadioSetPublicNetwork	8	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:752:13:RadioSetModem	16	static
+D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:2110:16:RadioSetTxGenericConfig	56	static
+D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1932:16:RadioSetRxGenericConfig	48	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1049:13:RadioSetTxConfig	56	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:860:13:RadioSetRxConfig	64	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:808:13:RadioIsChannelFree	64	static
+D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1311:23:RadioSend	32	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1278:17:RadioTimeOnAir	20	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1876:13:RadioTxPrbs	8	static
 D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio.c:1696:13:RadioIrqProcess	24	static

STM32CubeIDE/Release/Middlewares/SubGHz_Phy/radio_driver.d

@@ -48,10 +48,7 @@ Middlewares/SubGHz_Phy/radio_driver.o: \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
+ ../../Core/Inc/subghz.h ../../../../../../../Utilities/misc/stm32_mem.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
- ../../Core/Inc/stm32wlxx_nucleo_conf.h ../../Core/Inc/subghz.h \
- ../../../../../../../Utilities/misc/stm32_mem.h \
  ../../Core/Inc/utilities_conf.h \
  ../../../../../../../Drivers/CMSIS/Include/cmsis_compiler.h \
  ../../../../../../../Utilities/misc/stm32_tiny_vsnprintf.h \
@@ -110,9 +107,6 @@ D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/ra
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/subghz.h:
 ../../../../../../../Utilities/misc/stm32_mem.h:
 ../../Core/Inc/utilities_conf.h:

STM32CubeIDE/Release/Middlewares/SubGHz_Phy/radio_fw.d

@@ -57,10 +57,7 @@ Middlewares/SubGHz_Phy/radio_fw.o: \
  ../../Core/Inc/stm32wlxx_nucleo_conf.h \
  ../../Core/Inc/stm32wlxx_nucleo_errno.h \
  ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h \
+ ../../Core/Inc/subghz.h ../../LoRaWAN/Target/mw_log_conf.h \
- ../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h \
- ../../Core/Inc/stm32wlxx_nucleo_conf.h ../../Core/Inc/subghz.h \
- ../../LoRaWAN/Target/mw_log_conf.h \
  ../../../../../../../Utilities/trace/adv_trace/stm32_adv_trace.h \
  ../../LoRaWAN/Target/radio_board_if.h ../../Core/Inc/utilities_def.h \
  ../../Core/Inc/sys_debug.h ../../Core/Inc/sys_conf.h \
@@ -126,9 +123,6 @@ D://ONEDRIVE/STM32WLV13/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/ra
 ../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/stm32wlxx_nucleo_errno.h:
 ../../../../../../../Drivers/STM32WLxx_HAL_Driver/Inc/stm32wlxx_ll_gpio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_radio.h:
-../../../../../../../Drivers/BSP/STM32WLxx_Nucleo/stm32wlxx_nucleo_errno.h:
-../../Core/Inc/stm32wlxx_nucleo_conf.h:
 ../../Core/Inc/subghz.h:
 ../../LoRaWAN/Target/mw_log_conf.h:
 ../../../../../../../Utilities/trace/adv_trace/stm32_adv_trace.h: