try tps ...

Core/Src/gpio.c

@@ -50,13 +50,14 @@ void MX_GPIO_Init(void)
   __HAL_RCC_GPIOA_CLK_ENABLE();
   __HAL_RCC_GPIOB_CLK_ENABLE();
   __HAL_RCC_GPIOC_CLK_ENABLE();
-
+#if 1
   GPIO_InitStruct.Pin = GPIO_PIN_All;
   GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
-  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+  //HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
   HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
   HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+#endif
   //__HAL_RCC_GPIOA_CLK_DISABLE();
   //__HAL_RCC_GPIOB_CLK_DISABLE();
   __HAL_RCC_GPIOC_CLK_DISABLE();
@@ -67,6 +68,10 @@ void MX_GPIO_Init(void)
                           |LED3_Pin, GPIO_PIN_RESET);
 #endif
   /*Configure GPIO pin Output Level */
+
+
+  HAL_GPIO_WritePin(MEMS_POWER_GPIO_Port, MEMS_POWER_Pin, GPIO_PIN_RESET);
+
 #if defined(TOF_1)
   HAL_GPIO_WritePin(TOF_C_XSHUT_GPIO_Port, TOF_C_XSHUT_Pin, GPIO_PIN_SET);
 #endif
@@ -141,7 +146,7 @@ void MX_GPIO_Init(void)
 #if	(defined(TOF_1) && defined(TOF_2))
   GPIO_InitStruct.Pin = TOF_C_XSHUT_Pin;
   GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
-  GPIO_InitStruct.Pull = GPIO_PULLUP;
+  GPIO_InitStruct.Pull = GPIO_PULLDOWN;
   GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
   HAL_GPIO_Init(TOF_C_XSHUT_GPIO_Port, &GPIO_InitStruct);
 #endif
@@ -149,7 +154,7 @@ void MX_GPIO_Init(void)
 #if	(defined(TOF_2)&&defined(TOF_1))
   GPIO_InitStruct.Pin = TOF_L_XSHUT_Pin;
   GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
-  GPIO_InitStruct.Pull = GPIO_PULLUP;
+  GPIO_InitStruct.Pull = GPIO_PULLDOWN;
   GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
   HAL_GPIO_Init(TOF_L_XSHUT_GPIO_Port, &GPIO_InitStruct);
 #endif
@@ -206,11 +211,12 @@ HAL_GPIO_Init(SOAP_SWITCH_GPIO_Port, &GPIO_InitStruct);
   HAL_NVIC_SetPriority(EXTI1_IRQn, 0, 0);
   HAL_NVIC_EnableIRQ(EXTI1_IRQn);
 #endif
+#if 0
 #if	(defined(TOF_1) && defined(TOF_2))
   HAL_NVIC_SetPriority(TOF_C_INT_EXTI_IRQn, 0, 0);
   HAL_NVIC_EnableIRQ(TOF_C_INT_EXTI_IRQn);
 #endif
-
+#endif
 #if	(defined(TOF_2)&&!defined(TOF_1))
   HAL_NVIC_SetPriority(TOF_L_INT_EXTI_IRQn, 0, 0);
   HAL_NVIC_EnableIRQ(TOF_L_INT_EXTI_IRQn);

Core/Src/main.c

@@ -108,11 +108,34 @@ int main(void)
 
   /* Initialize all configured peripherals */
   MX_GPIO_Init();
+
+
+
+  while (1)
+
+   {
+	  HAL_GPIO_WritePin(MEMS_POWER_GPIO_Port, MEMS_POWER_Pin, GPIO_PIN_RESET);
+  	 HAL_Delay(5000);
+  	HAL_GPIO_WritePin(MEMS_POWER_GPIO_Port, MEMS_POWER_Pin, GPIO_PIN_SET);
+  	 HAL_Delay(5000);
+   }
+
+
+
+
+
   MX_DMA_Init();
 
   MX_I2C2_Init();
 
+ while (1)
 
+ {
+	 PME_OFF;
+	 HAL_Delay(5000);
+	 PME_ON;
+	 HAL_Delay(5000);
+ }
   MX_LoRaWAN_Init();
 
   /* USER CODE BEGIN 2 */

Core/Src/stm32_lpm_if.c

@@ -81,7 +81,9 @@ const struct UTIL_LPM_Driver_s UTIL_PowerDriver =
 void PWR_EnterOffMode(void)
 {
   /* USER CODE BEGIN EnterOffMode_1 */
-#if 1
+
+#if 0
+	PME_OFF;
 	HAL_GPIO_WritePin(GPIOA, GPIO_PIN_All&(~GPIO_PIN_9), GPIO_PIN_RESET);
 	HAL_GPIO_WritePin(GPIOB, GPIO_PIN_All&(~GPIO_PIN_5)&(~GPIO_PIN_3)&(~GPIO_PIN_4), GPIO_PIN_RESET);
 	HAL_GPIO_WritePin(GPIOC, GPIO_PIN_All, GPIO_PIN_RESET);
@@ -96,7 +98,7 @@ void PWR_EnterOffMode(void)
 void PWR_ExitOffMode(void)
 {
   /* USER CODE BEGIN ExitOffMode_1 */
-#if 1
+#if 0
 	HAL_ResumeTick();
 	return;
 #endif
@@ -107,8 +109,11 @@ void PWR_EnterStopMode(void)
 {
   /* USER CODE BEGIN EnterStopMode_1 */
 	//WORKABLE CONFIG
-	HAL_GPIO_WritePin(GPIOA, GPIO_PIN_All&(~GPIO_PIN_9), GPIO_PIN_RESET);
+	//PME_OFF;
-	HAL_GPIO_WritePin(GPIOB, GPIO_PIN_All&(~GPIO_PIN_5)&(~GPIO_PIN_3)&(~GPIO_PIN_4), GPIO_PIN_RESET);
+	//HAL_GPIO_WritePin(GPIOA, GPIO_PIN_All&(~GPIO_PIN_9), GPIO_PIN_RESET);
+	//HAL_GPIO_WritePin(GPIOB, GPIO_PIN_All&(~GPIO_PIN_5)&(~GPIO_PIN_3)&(~GPIO_PIN_4), GPIO_PIN_RESET);
+	HAL_GPIO_WritePin(GPIOA, GPIO_PIN_All, GPIO_PIN_RESET);
+	HAL_GPIO_WritePin(GPIOB, GPIO_PIN_All, GPIO_PIN_RESET);
 	HAL_GPIO_WritePin(GPIOC, GPIO_PIN_All, GPIO_PIN_RESET);
 
   /* USER CODE END EnterStopMode_1 */
@@ -140,7 +145,7 @@ void PWR_ExitStopMode(void)
     SRAM ctrls, DMAx, DMAMux, AES, RNG, HSEM  */
 
   /* Resume not retained USARTx and DMA */
-  //vcom_Resume();		//DON'T REMOVE THIS, KKEP LOW POWER
+  vcom_Resume();		//DON'T REMOVE THIS, KKEP LOW POWER
   /* USER CODE BEGIN ExitStopMode_2 */
   MX_GPIO_Init();
   MX_DMA_Init();

Core/Src/stm32wlxx_it.c

@@ -358,6 +358,7 @@ void DMA1_Channel7_IRQHandler(void)
   /* USER CODE END DMA1_Channel7_IRQn 1 */
 }
 #endif
+#if 0
 void EXTI3_IRQHandler(void)
 {
   /* USER CODE BEGIN EXTI3_IRQn 0 */
@@ -370,7 +371,7 @@ void EXTI3_IRQHandler(void)
 
   /* USER CODE END EXTI3_IRQn 1 */
 }
-
+#endif
 #if 0
 /**
   * @brief This function handles EXTI Lines [4] Interrupt.

Core/Src/yunhorn_sts_process.c

@@ -521,9 +521,10 @@ void STS_SENSOR_Power_ON(uint8_t cnt)
 		case 0:
 		case 1:
 		case 2:
-			PME_ON;
+			HAL_GPIO_WritePin(MEMS_POWER_GPIO_Port, MEMS_POWER_Pin, GPIO_PIN_SET);
 		break;
 		default:
+			HAL_GPIO_WritePin(MEMS_POWER_GPIO_Port, MEMS_POWER_Pin, GPIO_PIN_SET);
 		break;
 	}
 
@@ -534,9 +535,10 @@ void STS_SENSOR_Power_OFF(uint8_t cnt)
 		case 0:
 		case 1:
 		case 2:
-			PME_OFF;
+			HAL_GPIO_WritePin(MEMS_POWER_GPIO_Port, MEMS_POWER_Pin, GPIO_PIN_RESET);
 		break;
 		default:
+			HAL_GPIO_WritePin(MEMS_POWER_GPIO_Port, MEMS_POWER_Pin, GPIO_PIN_RESET);
 		break;
 	}
 }

STM32CubeIDE/.settings/language.settings.xml

@@ -5,7 +5,7 @@
 			<provider copy-of="extension" id="org.eclipse.cdt.ui.UserLanguageSettingsProvider"/>
 			<provider-reference id="org.eclipse.cdt.core.ReferencedProjectsLanguageSettingsProvider" ref="shared-provider"/>
 			<provider-reference id="org.eclipse.cdt.managedbuilder.core.MBSLanguageSettingsProvider" ref="shared-provider"/>
-			<provider class="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" console="false" env-hash="-877539789554811708" id="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" keep-relative-paths="false" name="MCU ARM GCC Built-in Compiler Settings" parameter="${COMMAND} ${FLAGS} -E -P -v -dD &quot;${INPUTS}&quot;" prefer-non-shared="true">
+			<provider class="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" console="false" env-hash="-752586124573436390" id="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" keep-relative-paths="false" name="MCU ARM GCC Built-in Compiler Settings" parameter="${COMMAND} ${FLAGS} -E -P -v -dD &quot;${INPUTS}&quot;" prefer-non-shared="true">
 				<language-scope id="org.eclipse.cdt.core.gcc"/>
 				<language-scope id="org.eclipse.cdt.core.g++"/>
 			</provider>
@@ -16,7 +16,7 @@
 			<provider copy-of="extension" id="org.eclipse.cdt.ui.UserLanguageSettingsProvider"/>
 			<provider-reference id="org.eclipse.cdt.core.ReferencedProjectsLanguageSettingsProvider" ref="shared-provider"/>
 			<provider-reference id="org.eclipse.cdt.managedbuilder.core.MBSLanguageSettingsProvider" ref="shared-provider"/>
-			<provider class="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" console="false" env-hash="-877539789554811708" id="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" keep-relative-paths="false" name="MCU ARM GCC Built-in Compiler Settings" parameter="${COMMAND} ${FLAGS} -E -P -v -dD &quot;${INPUTS}&quot;" prefer-non-shared="true">
+			<provider class="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" console="false" env-hash="-752586124573436390" id="com.st.stm32cube.ide.mcu.toolchain.armnone.setup.CrossBuiltinSpecsDetector" keep-relative-paths="false" name="MCU ARM GCC Built-in Compiler Settings" parameter="${COMMAND} ${FLAGS} -E -P -v -dD &quot;${INPUTS}&quot;" prefer-non-shared="true">
 				<language-scope id="org.eclipse.cdt.core.gcc"/>
 				<language-scope id="org.eclipse.cdt.core.g++"/>
 			</provider>