History

Yunhorn efad58929d first		2022-10-01 12:37:32 +08:00
..
README.md	first	2022-10-01 12:37:32 +08:00

README.md

Wio Terminal Light Sensor

In this section, we will detail how the sensors work, how to get sensor data using Wio Terminal and how to send the data out using Wio Terminal & Grove - Wio-E5.

Working Principle of Sensors

In this section we need to learn to use the light sensor built into the Wio Terminal.

Light sensor is a sensor that uses a photoelectric element as a detection element. It first converts the measured light changes into light signal changes, and then further converts the light signal into an electrical signal with the help of a photoelectric element. A light sensor generally consists of three parts: a light source, an optical path and a photoelectric element.

For more information on the use of light sensors its reference here.

Materials Required


Wio Terminal	Grove - Wio-E5

Preliminary Preparation

Connection

In this routine, we need to connect to a nearby LoRa® gateway with the help of Grove - Wio-E5. We need to configure the Grove port on the right side of the Wio Terminal as a soft serial port to receive AT commands.

!!!Note Why not use the Grove port on the left? > The Grove interface on the left is IIC capable, and we use the IIC interface for most sensors, so keeping it is a better solution.

Software preparation

Step 1. You need to Install an Arduino Software.

Step 2. Launch the Arduino application.

Step 3. Add Wio Terminal to the Arduino IDE.

Open your Arduino IDE, click on File > Preferences, and copy below url to Additional Boards Manager URLs:

https://files.seeedstudio.com/arduino/package_seeeduino_boards_index.json

Click on Tools > Board > Board Manager and Search Wio Terminal in the Boards Manager.

Step 4. Select your board and port

You'll need to select the entry in the Tools > Board menu that corresponds to your Arduino. Selecting the Wio Terminal.

Select the serial device of the Wio Terminal board from the Tools -> Port menu. This is likely to be COM3 or higher (COM1 and COM2 are usually reserved for hardware serial ports). To find out, you can disconnect your Wio Terminal board and re-open the menu; the entry that disappears should be the Arduino board. Reconnect the board and select that serial port.

!!!Tip For Mac User, it will be something like /dev/cu.usbmodem141401.

If you are not able to upload the sketch, mostly it's because Arduino IDE was not able to put Wio Terminal to bootloader mode. (Because MCU was halted or your program handling USB) Workaround is putting your Wio Terminal to bootloader mode manually.

<div align=center><img width=400 src="https://files.seeedstudio.com/wiki/Wio-Terminal/img/Wio-Terminal-Bootloader.png"/></div>

Step 5. Download Grove - Wio-E5 Library

Visit the Disk91_LoRaE5 repositories and download the entire repo to your local drive.

Step 6. Adding libraries to the Arduino IDE

Now, the 3-Axis Digital Accelerometer library can be installed to the Arduino IDE. Open the Arduino IDE, and click sketch -> Include Library -> Add .ZIP Library, and choose the Disk91_LoRaE5 file that you've have just downloaded.

Get the value of the built-in light sensor of Wio Terminal

This repo demonstrates how to use the built-in light sensor as a component in Wio Terminal. The light sensor uses analog interface and you can simply read the surrounding light sensor values via reading its pin.

void setup() {
  pinMode(WIO_LIGHT, INPUT);
  Serial.begin(115200);
}
 
void loop() {
   int light = analogRead(WIO_LIGHT);
   Serial.print("Light value: ");
   Serial.println(light);
   delay(200);
}

!!!Note WIO_LIGHT is the pin for built-in light Sensor. The light sensor is connected to A13.

The light sensor is at the back of the Wio Terminal, just above the microSD card slot.

<td align="center"><div align=center><img width = 300 src="https://files.seeedstudio.com/wiki/K1100/20.png"/></div></td>

Open the serial monitor of Arduino IDE and select the baud rate as 115200 and observe the result.

Send data via Grove - Wio-E5

We combine the previous code of Grove - Wio-E5 to connect to the LoRa® network. Using the AT command it is possible to send the value of the light sensor to the LoRa® network.

As we know from the code in the section above to get the light sensor value, the light value obtained is an integer data of less than eight bits.

In this way, we determine the content, size and format of the data to be sent via the AT command. We might as well set up a large enough array, store the strings we need to send into the array, and finally use the send_sync() function to send the array out.

The pseudo-code for the above idea is roughly as follows.

......
  int light = analogRead(WIO_LIGHT);  //Get the Wio Terminal light value.

  static uint8_t data[2] = { 0x00 };  //Use the data[] to store the values of the sensors

  data_decord(light, data);
  
  if ( lorae5.send_sync(              //Sending the sensor values out
        8,                            // LoRaWan Port
        data,                         // data array
        sizeof(data),                 // size of the data
        false,                        // we are not expecting a ack
        7,                            // Spread Factor
        14                            // Tx Power in dBm
       ) 
  )
......

The rest of what we need to do is to use the begin() function to initialize Grove - Wio-E5 and the setup() function to configure the triplet information of Grove - Wio-E5. When we send a data message using the send_sync() function, we will try to join the LoRaWAN® at the same time, and once it succeeds, the data will be sent and information such as signal strength and address will be returned.

The full code example can be found here.

!!!Tip We do not recommend that you upload the code now to see the results, because at this point you have not yet configured Helium/TTN and will get a "Join failed" result. We recommend that you upload this code after you have completed the Connecting to Helium or Connecting to TTN chapter to complete the complete data sending process.

Once you have experienced and understood how the light sensor works and the data format, please continue with the next step of the tutorial join LoRaWAN®.

Helium Section
	Helium Introduction In this chapter, we will introduce the Helium console controls that we use to get a first impression of the Helium console. Jump to chapter >
	Connecting to Helium This section describes how to configure Helium so that sensor data can be successfully uploaded to and displayed in Helium. Jump to chapter >
TTN Section
	TTN Introduction In this chapter, we will introduce the TTN console controls that we use to get a first impression of the TTN console. Jump to chapter >
	Connecting to TTN This section describes how to configure TTN so that sensor data can be successfully uploaded to and displayed in TTN. Jump to chapter >

Tech Support

Please do not hesitate to submit the issue into our forum.

Upgradable to Industrial Sensors SenseCAP K1100 serves as a gateway to the higher-end SenseCAP LoRaWAN® series of industrial outdoor sensors. Users can prototype multiple AIoT applications with this kit, after which they can scale them up to the robust, long-life, and industrial SenseCAP sensors.

Statement

The LoRa® Mark is a trademark of Semtech Corporation or its subsidiaries.
LoRaWAN® is a mark used under license from the LoRa Alliance®.